How to clear fault codes Yale and Hyster forklift
Understanding and addressing the most prevalent error codes for Yale and Hyster forklifts is crucial for effective diagnostics and troubleshooting.
Fault codes on Yale and Hyster forklifts can either display visibly or reside within the system.
To accurately diagnose and resolve these issues, refer to the table below for a comprehensive list of error codes along with detailed descriptions and potential causes.
if you have any questions you can leave the question here Forklift Error codes and our technicians can help you
| Fault Codes | Diagnostic Codes | Possible Cases |
|---|---|---|
| 524223-0 | XMSN Reverse Pressure Greater Than Commanded Pressure | A. SENSOR SUPPLY OPEN CIRCUIT B. SENSOR FAILURE C. FUNCTIONAL FAILURE — MECHANICAL D. FUNCTIONAL FAILURE IN CONTROLLER |
| 524225-0 | XMSN Forward Pressure Greater Than Commanded Pressure | |
| 524223-1 | XMSN Reverse Pressure Less Than Commanded | A. LOW TRANSMISSION OIL LEVEL B. SENSOR SUPPLY OPEN CIRCUIT C. SENSOR FAILURE D. FUNCTIONAL FAILURE — MECHANICAL E. FUNCTIONAL FAILURE IN CONTROLLER |
| 524225-1 | XMSN Forward Pressure Less Than Commanded | |
| 105-3 | Intake Air Temperature (IAT) Sensor OORH | A. SENSOR WIRING OPEN CIRCUIT B. SENSOR SIGNAL SHORTED TO 5V OR BATTERY VOLTAGE C. SENSOR FAILURE D. FUNCTIONAL FAILURE IN CONTROLLER |
| 110-3 | Coolant Temperature Sensor OORH | |
| 177-3 | Transmission Oil Temperature Sensor OORH | |
| 522603-3 | Fuel Temp (LPG) Sensor OORH | |
| 105-4 | Intake Air Temperature (IAT) Sensor OORL | A. SENSOR SIGNAL SHORTED TO SENSOR GROUND. B. SENSOR SIGNAL SHORTED TO FRAME GROUND. C. SENSOR FAILURE D. FUNCTIONAL FAILURE IN CONTROLLER |
| 110-4 | Coolant Temperature Sensor OORL | |
| 177-4 | Transmission Oil Temperature Sensor OORL | |
| 522603-4 | Fuel Temp (LPG) Sensor OORL | |
| 522712-3 | Accelerator A Position Sensor OORH | A. SENSOR SUPPLY OPEN CIRCUIT (SENSOR SIGNAL GROUNDS) B. B SENSOR SIGNAL OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO BATTERY SOURCE D. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY |
| 522713-3 | Accelerator B Position Sensor OORH | |
| 522712-4 | Accelerator A Position Sensor OORL | A. SENSOR SUPPLY OPEN CIRCUIT (+5 VOLTS) B. SENSOR SIGNAL A OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO FRAME GROUND D. SENSOR SIGNAL SHORTED TO SENSOR GROUND E. SENSOR FAILURE F. FUNCTIONAL FAILURE IN CONTROLLER |
| 522713-4 | Accelerator B Position Sensor OORL | |
| 1079-31 | 5VE1 & 5VE2 Simultaneously OORH | A. ELECTRONIC THROTTLE ASSEMBLY (ETA) STICKY B. SENSOR (ETA) FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 51-2 | Throttle Position Sensor Signals A and B Not Tracking Correctly | |
| 51-7 | Throttle Position Sensor Signals A and B Not At Commanded Value | |
| 51-31 | Throttle Position Sensor 1 & 2 Out of Range | |
| 2350-3 | DTC 2350-3 - Front Work Lights Relay (RL4) Driver Output OORH | A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED B. SHORT ON RELAY DRIVER OUTPUT TO UNSWITCHED BATTERY (SEEWARNING BEFORE CONTINUING) C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY. D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT G. FUNCTIONAL FAILURE IN CONTROLLER |
| 522710-3 | Throttle A Position Sensor OORH | A. SENSOR GROUND OPEN CIRCUIT B. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY C. SENSOR SIGNAL SHORTED TO BATTERY SOURCE D. SENSOR FAILURE E. FUNCTIONAL FAILURE IN CONTROLLER |
| 522711-3 | Throttle B Position Sensor OORH | |
| 522710-4 | Throttle A Position Sensor OORL | A. SENSOR SIGNAL OPEN CIRCUIT B. SENSOR SUPPLY OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO FRAME GROUND D. SENSOR SIGNAL SHORTED TO SENSOR GROUND E. SENSOR FAILURE F. FUNCTIONAL FAILURE IN CONTROLLER |
| 522711-4 | Throttle B Position Sensor OORL | |
| 521-3 | Brake Pedal Position Sensor OORH | A. SENSOR GROUND OPEN CIRCUIT B. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY C. SENSOR SIGNAL SHORTED TO BATTERY D. SENSOR FAILURE E. FUNCTIONAL FAILURE IN CONTROLLER |
| 523780-3 | Park Brake Position Sensor OORH | |
| 524245-3 | Seat Occupancy Position Sensor OORH | |
| 521-4 | Brake Pedal Position Sensor OORL | A. SENSOR SUPPLY OPEN CIRCUIT B. SENSOR SIGNAL OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO SENSOR GROUND D. SENSOR SIGNAL SHORTED TO FRAME GROUND E. SENSOR FAILURE F. FUNCTIONAL FAILURE IN CONTROLLER |
| 523780-4 | Park Brake Position Sensor OORL | |
| 524245-4 | Operator Presence System Sensor OORL | |
| 523833-3 | Glow Plug Relay Driver Output OORH | A. COIL DRIVER OUTPUT SHORTED TO BATTERY. B. FUNCTIONAL FAILURE IN CONTROLLER. |
| 524195-3 | Cold Start Relay Driver Output OORH | |
| 523833-4 | Glow Plug Relay Driver Output OORL | A. COIL DRIVER OUTPUT SHORTED TO GROUND. B. FUNCTIONAL FAILURE IN CONTROLLER. |
| 524195-4 | Cold Start Relay Driver Output OORL | |
| 1079-31 | 5VE1 & 5VE2 Simultaneously OORH | A. 5 VOLT "E1" SUPPLY SHORTED TO SYSTEM SUPPLY SOURCE B. 5 VOLT "E2" SUPPLY SHORTED TO SYSTEM SUPPLY SOURCE C. 5VOLT E1 AND E2 SIMULTANEOUSLY SHORTED TO SYSTEM SUPPLY SOURCE D. FUNCTIONAL FAILURE IN CONTROLLER |
| 524260-3 | 5VE2 Sensor Supply Circuit Voltage OORH | |
| 524261-3 | 5VE1 Sensor Supply Circuit Voltage OORH | |
| 96-3 | Fuel Level Sensor OORH | A. SENSOR SIGNAL SHORTED TO BATTERY B. SENSOR SIGNAL/RETURN OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO GROUND D. SENSOR FAILURE |
| 96-4 | Fuel Level Sensor OORL | |
| 523833-3 | Glow Plug Relay Driver Output OORH | A. COIL DRIVER OUTPUT SHORTED TO SYSTEM VOLTAGE B. COIL SHORT CIRCUIT C. FUNCTIONAL FAILURE IN CONTROLLER |
| 523920-3 | REV Circuit Shorted High | |
| 523930-3 | FWD Circuit Shorted High | |
| 524195-3 | Cold Start Relay Driver Output OORH | |
| 524269-3 | Transmission Enable Valve Coil Driver Output OORH | |
| 523920-4 | REV Circuit Shorted Low | A. COIL DRIVER OUTPUT SHORTED TO GROUND B. COIL/WIRING OPEN CIRCUIT C. FUNCTIONAL FAILURE IN CONTROLLER |
| 523930-4 | FWD Circuit Shorted Low | |
| 524269-4 | Transmission Enable Valve Coil Driver Output OORL | |
| 522606-10 | Post Catalytic Converter Oxygen (O2) Sensor (Slow Response) | A. OXYGEN (O2) SENSOR FAILURE B. FUNCTIONAL FAILURE IN CONTROLLER |
| 522737-10 | Pre Catalytic Converter Oxygen (O2) Sensor (Slow Response) | |
| 2000-12 | CAN Tx Failure | A. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO B. CAN HI AND CAN LO SHORTED TOGETHER C. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES D. STG ON CAN HI E. STS/STB ON CAN LO F. CAN CONNECTED DEVICE FAILURE |
| 2000-12 | CAN Rx Failure | |
| 2000-14 | CANbus Address Conflict Failure | |
| 522593-12 | DTC 522593-12 - CANbus Communication Loss - ECU to EPR | |
| 524233-14 | DTC 524233-14 - Boost Test Override | A. DISPLAY INTERNAL FAILURE |
| 524234-14 | DTC 524234-14 - Internal Processing Error | |
| 524236-XX | DTC 524236-XX - Boost Test Failure | |
| 190-2 | DTC 190-2 - Engine RPM Sensor Output Is Less Than Engine Speed | A. OPEN CIRCUIT IN SENSOR SUPPLY B. SENSOR SIGNAL OPEN CIRCUIT OR SHORT TO GROUND C. SENSOR SIGNAL SHORTED TO BATTERY SOURCE D. SENSOR FAILURE E. FUNCTIONAL FAILURE IN CONTROLLER |
| 190-7 | DTC 190-7 - Engine Speed Exceeds Command | |
| 522120-1 | DTC 522120-1 - Engine RPM Higher than XMSN Limit | |
| 522585-2 | DTC 522585-2 - Engine RPM Sensor (Mazda Gas ECU) | |
| 523740-3 | DTC 523740-3 - Truck has NO Forward or Reverse Motion | A. HIGH EXTERNAL MAGNETIC FIELDS B. DIRECTIONAL LEVER MECHANISM/MAGNETIC FAILURE C. DISPLAY SWITCH CLUSTER (DSC) FAILURE |
| 523740-4 | DTC 523740-4 - Truck has NO Forward or Reverse Motion | |
| 524255-3 | DTC 524255-3 - DSC Temperature OORH | A. DISPLAY SWITCH CLUSTER (DSC) IS OVERHEATED |
| 524255-4 | DTC 524255-4 - DSC Temperature OORL | |
| 524255-3 | DTC 524255-3 - DSC Temperature OORH | A. DISPLAY SWITCH CLUSTER (DSC) IS OVERHEATED |
| 524255-4 | DTC 524255-4 - DSC Temperature OORL | |
| 524255-3 | DTC 524255-3 - DSC Temperature OORH | A. DISPLAY SWITCH CLUSTER (DSC) IS OVERHEATED |
| 524255-4 | DTC 524255-4 - DSC Temperature OORL | |
| 522655-0 | DTC 522655-0 - Short Term Closed Loop Correction Bank 1 Less Than NOR -35% (Rich Engine Operation) | A. PROBLEMS THAT MAY CAUSE LEAN ENGINE OPERATION B. PROBLEMS THAT MAY CAUSE RICH ENGINE OPERATION C. SENSOR FAILURE D. FUNCTIONAL FAILURE IN CONTROLLER |
| 522655-1 | DTC 522655-1 - Short Term Closed Loop Correction Bank 1 Greater Than NOR 35% (Lean Engine Operation) | |
| 522660-0 | DTC 522660-0 - Long Term Closed Loop Correction Bank 1 Less Than NOR -30% (Rich Engine Operation) | |
| 522660-1 | DTC 522660-1 - Long Term Closed Loop Correction Bank 1 Greater Than NOR 30% (Lean Engine Operation) | |
| 523767-2 | DTC 523767-2 - DSC Fault - Arrow Down Button Stuck | A. BUTTON FAILURE |
| 523769-2 | DTC 523769-2 - DSC Fault - Arrow Up Button Stuck | |
| 524206-2 | DTC 524206-2 - DSC Fault - Rear Worklight Button Stuck | |
| 524208-2 | DTC 524208-2 - DSC Fault - Front Worklight Button Stuck | |
| 524209-2 | DTC 524209-2 - DSC Fault - Hourmeter Button Stuck | |
| 190-2 | DTC 190-2 - Crank Loss (CAM Pulse without Crank Pulse) | A. DUST/DEBRIS IN SENSOR HOUSING B. TIMING BELT NOT TENSIONED PROPERLY C. SENSOR OPEN CIRCUIT GROUND/OPEN CIRCUIT SUPPLY D. SENSOR OPEN CIRCUIT SIGNALS E. SENSOR SHORTED CIRCUIT SIGNALS F. SENSOR FAILURE G. FUNCTIONAL FAILURE IN CONTROLLER |
| 190-4 | DTC 190-4 - Crank Loss (CAM Pulse without Crank Pulse) | |
| 190-8 | DTC 190-8 - Crank/CAM Synchronization | |
| 522752-2 | DTC 522752-2 - Crank Loss (CAM Pulse without Crank Pulse) | |
| 522752-4 | DTC 522752-4 - CAM Loss (Crank Pulse without CAM Pulse) | |
| 522595-12 | DTC 522595-12 - Internal Circuity Fault Detection | A. EPR FAILURE |
| 522596-12 | DTC 522596-12 - Internal Circuity Fault Detection | |
| 524266-31 | DTC 524266-31 - Electronic Throttle Motor/Motor Connections - Short Circuit | A. CONNECTION SHORT CIRCUIT B. ETB MOTOR SHORT CIRCUIT C. ECU/ETB DRIVER FAILURE |
| 524286-31 | DTC 524286-31 - ECU - ETB Driver Component Failure | |
| 94-0 | DTC 94-0 - Primary Fuel Pressure Higher Than Expected | A. FUEL PRESSURE SENSOR WIRING FAULT B. FUEL PRESSURE FAULT C. FAULTY CONTROLLER |
| 94-1 | DTC 94-1 - Primary Fuel Pressure Lower Than Expected | |
| 520260-3 | DTC 520260-3 - Electronic Pressure Regulator (EPR) OORH | A. DEPR WIRING FAULT B. DEPR FAULT |
| 520260-4 | DTC 520260-4 - Electronic Pressure Regulator (EPR) OORL | |
| 91-2 | DTC 91-2 Sensor Signals A and B Not Tracking Correctly | A. DIFFERENCE BETWEEN SENSORS IS BEYOND ALLOWABLE TOLERANCE B. SENSOR FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 515-0 | DTC 515-0 RPM Greater Than Throttle Command | A. LARGE LEAKS IN MANIFOLD B. ELECTRONIC THROTTLE ASSEMBLY (ETA) MECHANICAL ISSUES C. FUNCTIONAL FAILURE IN CONTROLLER |
| 522764-6 | DTC 522764-6 Ign/Alt - Ignition 1 Relay (RL6) Driver Output OORL | A. SHORTED RELAY COIL B. SHORT TO GROUND ON PDM RELAY DRIVER OUTPUT C. FUNCTIONAL FAILURE IN DISPLAY (DSC) |
| 168-0 | DTC 168-0 System Battery Voltage OORH | A. BATTERY FAILURE B. ALTERNATOR FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 168-1 | DTC 168-1 System Battery Voltage OORL | A. BLOWN FUSE OR FAULTY WIRING HARNESS B. IGNITION WIRE FAILURE C. BATTERY FAILURE D. ALTERNATOR FAILURE E. OPERATION CYCLE TOO SHORT TO CHARGE BATTERY F. QUIESCENT CURRENT DRAW TOO HIGH DURING TRUCK OFF TIME |
| 522697-12 | DTC 522697-12 Internal Central Processor or Circuitry Faults | A. FUNCTIONAL FAILURE IN ECU CONTROLLER |
| 108-1 | DTC 108-1 Barometric Pressure Below Acceptable Limit | A. OPEN CIRCUIT SENSOR SUPPLY B. SHORTED SIGNAL CIRCUIT TO BATTERY/SENSOR SUPPLY – SIGNAL OPEN CIRCUIT C. SENSOR FAILURE D. FUNCTIONAL FAILURE IN CONTROLLER |
| 523550-3 | DTC 523550-3 Start Relay Control OORH | A. HARNESS/PDM SHORT CIRCUIT TO SWITCHED OR UNSWITCHED BATTERY B. FUNCTIONAL FAILURE IN CONTROLLER |
| 522604-3 | DTC 522604-3 Fuel Run Relay Control OORH | A. HARNESS/PDM SHORT CIRCUIT TO SWITCHED OR UNSWITCHED BATTERY B. FUNCTIONAL FAILURE IN CONTROLLER |
| 522604-4 | DTC 522604-4 Fuel Relay PWM Control OORL | A. OPEN CIRCUIT B. HARNESS/PDM SHORT TO GROUND C. FUNCTIONAL FAILURE IN CONTROLLER |
| 522604-5 | DTC 522604-5 Fuel Relay not Functioning | A. HARNESS RELAY COIL OPEN CIRCUIT B. FUNCTIONAL FAILURE IN CONTROLLER |
| 522598-3 | DTC 522598-3 LPG Lock Off OORH | A. COIL TO ECU HARNESS SHORTED TO UNSWITCHED OR SWITCH BATTERY B. COIL SHORTED TURNS C. FUNCTIONAL FAILURE IN CONTROLLER |
| 522598-4 | DTC 522598-4 LPG Lock Off OORL | A. COIL TO ECU HARNESS OPEN CIRCUIT B. COIL TO ECU HARNESS SHORT TO GROUND C. COIL OPEN CIRCUIT D. COIL SUPPLY OPEN CIRCUIT E. FUNCTIONAL FAILURE IN CONTROLLER |
| 522592-0 | EPR Pressure Greater Than Commanded | A. WORN OR DAMAGED PRIMARY OR SECONDARY SEAT B. FAULTY ELECTRONIC PRESSURE REGULATOR (EPR) ELECTRICAL CONNECTIONS C. EPR FAILURE |
| 522592-1 | EPR Pressure Less Than Commanded | A. LOW SECONDARY FUEL PRESSURE DUE TO A FUEL RESTRICTION B. FAULTY ELECTRONIC PRESSURE REGULATOR (EPR) ELECTRICAL CONNECTIONS C. EPR FAILURE |
| 524227-3 | Manual Hydraulic Lockout Coil OORH | A. COIL DRIVER OUTPUT SHORTED TO BATTERY B. COIL SHORT C. FUNCTIONAL FAILURE IN CONTROLLER |
| 524227-4 | Manual Hydraulic Lockout Coil OORL | A. COIL DRIVER OUTPUT SHORTED TO GROUND B. WIRING/COIL OPEN CIRCUIT C. FUNCTIONAL FAILURE IN CONTROLLER |
| 1239-7 | Fuel Run-Out Longer Than Expected | A. LOCK-OFF SOLENOID WIRING FAULT B. LOCK-OFF SOLENOID FAULT C. FAULTY CONTROLLER |
| 524230-3 | Rear Work Lights Relay (RL7) Driver Output OORH | A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED B. SHORT ON RELAY DRIVER OUTPUT TO UNSWITCHED BATTERY (SEE WARNING BEFORE CONTINUING) C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY. D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT G. FUNCTIONAL FAILURE IN CONTROLLER |
| 524230-4 | Rear Work Lights Relay (RL7) Driver Output OORL | A. SHORTED RELAY COIL B. SHORT TO GROUND ON PDM RELAY DRIVER OUTPUT C. FUNCTIONAL FAILURE IN CONTROLLER |
| 522631-2 | Pre-Cat Bank 1 Sensor Fails To Switch To Rich | |
| 522762-4 | Switched Battery Voltage 3 (IGN 3) OORL | A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND D. FUNCTIONAL FAILURE IN CONTROLLER |
| 522772-4 | Backup Lamp Driver Output OORL | A. LAMP DRIVER OUTPUT SHORTED TO GROUND B. FUNCTIONAL FAILURE IN CONTROLLER |
| 880-4 | Stop Lamp Driver Output OORL | A. LAMP DRIVER OUTPUT SHORTED TO GROUND B. FUNCTIONAL FAILURE IN CONTROLLER |
| 522760-4 | Switched Battery Voltage 1 (IGN 1) OORL | A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND D. FUNCTIONAL FAILURE IN CONTROLLER |
| 524260-1 | 5 Volt Supply Circuit B OORL | A. 5 VOLT "A" SHORTED TO GROUND B. 5 VOLT "B" SHORTED TO GROUND C. 5 VOLT "C" SHORTED TO GROUND D. VSM FAILURE E. 5 VOLT ECU POWER SUPPLY SHORTED TO GROUND |
| 522614-7 | Throttle Not at Limp Mode Position (GM Engines Only) | A. MECHANISM STICKY COMPONENT OPERATIONAL CHECK PROCEDURE OR ACTION: 1. Turn power to OFF for no less than 30 seconds, and then to ON to clear displayed DTC. Does reported DTC to reoccur? YES: Go to Step 2. NO: Problem not verified. Resume operation. 2. Conduct a quick visual inspection of all connectors/wiring associated with the displayed fault code. Are any faults detected/observed? YES: Repair/replace connector or wiring associated with faults found. See Electrical System 2200 SRM 1142. NO: Go to Cause A. CAUSE A - MECHANISM STICKY PROCEDURE OR ACTION: 1. Turn truck power ON and start engine. 2. Check for proper operation of the throttle body and the ECU mechanism by exercising the accelerator pedal with the vehicle in neutral. For GM 2.4L gasoline and LPG engines, the engine should idle at 775 to 825 rpm with no pedal and continuing to the governor speed which should be 2675 to 2725 rpm at full pedal. For GM 4.3L gasoline and LPG engines the engine should idle at 725 to 775 rpm with no pedal and continuing to the governor speed which should be 2375 to 2425 rpm at maximum full pedal. Is the throttle mechanism operating smoothly/tracking with accelerator operation? YES: Problem corrected. Resume operation. NO: Ensure truck power is OFF. Clean any fuel residue from mechanism and go to Step 3. 3. Check for proper operation of the throttle body and the ECU mechanism by exercising the accelerator pedal with the vehicle in neutral. For GM 2.4L gasoline and LPG engines, the engine should idle at 775 to 825 rpm with no pedal and continuing to the governor speed which should be 2675 to 2725 rpm at full pedal. For GM 4.3L gasoline and LPG engines the engine should idle at 725 to 775 rpm with no pedal and continuing to the governor speed which should be 2375 to 2425 rpm at maximum full pedal. Is the throttle mechanism operating smoothly/tracking with accelerator operation? YES: Problem corrected. Resume operation. NO: Ensure truck power is OFF. Replace Electronic Throttle Body. For GM 2.4L Gasoline engines see Gasoline Fuel System, GM 2.4L Engine 900 SRM 1126. For GM 2.4L LPG engines see LPG Fuel System, GM 2.4L Engine 900 SRM 1124. For GM 4.3L Gasoline engine see Gasoline Fuel System, GM 4.3L Engine With GFI 900 SRM 1244. For GM 4.3L LPG engine see LPG Fuel System, GM 4.3L Engine With GFI 900 SRM 1242. |
| 522616-8 | Throttle Not at Command Position (GM Engines Only) | |
| 522617-5 | Throttle Not at Fully Closed/Open Position (GM Engines Only) | |
| 522760-3 | Switched Battery Voltage 1 (IGN 1) OORH | A. IGN VOLTAGE SHORTED TO UNSWITCHED BATTERY SOURCE IN PDM OR PDM/VSM HARNESS B. IGN VOLTAGE SHORTED TO UNSWITCHED BATTERY SOURCE IN PDM OUTPUT HARNESS C. IGN VOLTAGE SHORTED TO SWITCHED BATTERY SOURCE IN PDM OR PDM/VSM HARNESS D. IGN 2 VOLTAGE SHORTED TO BATTERY SOURCE E. FUNCTIONAL FAILURE IN CONTROLLER |
| 135-16 | Fuel Air Pressure minus (MAP) OORH (GM LPG Only) or and Fuel Absolute Pressure Minus (MAP) Too High | |
| 524240-4 | Washer Pump Drive Command OORL | windshield wiper pump |
| 522125-8 | Transmission Range1 Valve Current Out Of Range (TCU) | A. HIGH RESISTIVE CONNECTION B. VALVE -VE SHORTED TO BATTERY – VE/FRAME GROUND C. FUNCTIONAL FAILURE IN CONTROLLER |
| 676-3 | Glow Plug Relay Driver Output OORH | A. RELAY/COIL DRIVER OUTPUT SHORTED TO BATTERY B. RELAY/COIL DRIVER OUTPUT OPEN CIRCUIT C. RELAY/COIL DRIVER RETURN OPEN CIRCUIT D. FUNCTIONAL FAILURE IN CONTROLLER |
| 524223-4 | Transmission Reverse Pressure OORL | A. SENSOR SUPPLY OPEN CIRCUIT B. SENSOR SIGNAL OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO SENSOR GROUND D. SENSOR SIGNAL SHORTED TO FRAME GROUND E. SENSOR FAILURE F. FUNCTIONAL FAILURE IN CONTROLLER |
| 100-4 | Engine Oil Pressure OORL | A. SENSOR SUPPLY OPEN CIRCUIT B. SENSOR SIGNAL OPEN CIRCUIT C. SENSOR SIGNAL SHORTED TO SENSOR GROUND D. SENSOR SIGNAL SHORTED TO FRAME GROUND E. SENSOR FAILURE F. FUNCTIONAL FAILURE IN CONTROLLER |
| 524224-0 | XMSN Forward 2 Pressure Greater Than Commanded Pressure | A. SENSOR SUPPLY OPEN CIRCUIT B. SENSOR FAILURE C. FUNCTIONAL FAILURE — MECHANICAL |
| 168-4 | System Battery Voltage OORL | A. BATTERY FAILURE B. ALTERNATOR FAILURE C. OPERATION CYCLE TOO SHORT TO CHARGE BATTERY D. QUIESCENT CURRENT DRAW TOO HIGH DURING TRUCK OFF TIME |
| 654-5 | GM Gas Drive Injector 4 Open or Circuit Cummins-Code 332. See QSB 3.3L Troubleshooting and Repair | A. FUEL INJECTOR OPEN CIRCUIT B. INJECTOR DRIVER MODULE FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 524263-1 | Uncommanded Power Down | A. TCU PROGRAM CORRUPTED OR TCU APPLICATION FILE MISMATCH B. FUNCTIONAL FAILURE IN CONTROLLER |
| 651-5 | GM Gas Drive Injector 1 Open Circuit,or Cummins-Code 322. See QSB 3.3L Troubleshooting and Repair | A. FUEL INJECTOR OPEN CIRCUIT B. INJECTOR DRIVER MODULE FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 652-5 | GM Gas Drive Injector 2 Open Circuit | A. FUEL INJECTOR OPEN CIRCUIT B. INJECTOR DRIVER MODULE FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 653-5 | Cummins-Code 324. See QSB 3.3L Troubleshooting and Repair | A. FUEL INJECTOR OPEN CIRCUIT B. INJECTOR DRIVER MODULE FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 655-5 | GM Gas Drive Injector 5 Open Circuit | A. FUEL INJECTOR OPEN CIRCUIT B. INJECTOR DRIVER MODULE FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 656-5 | GM Gas Drive Injector 6 Open Circuit | A. FUEL INJECTOR OPEN CIRCUIT B. INJECTOR DRIVER MODULE FAILURE C. FUNCTIONAL FAILURE IN CONTROLLER |
| 2023-12 | CANbus Error With Display | A. TERMINATION RESISTOR(S) OPEN CIRCUIT B. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO C. CAN HI AND CAN LO SHORTED TOGETHER D. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES E. STG ON CAN HI F. STS/STB ON CAN LO G. CAN CONNECTED DEVICE FAILURE |
1. maker : hyster
2. model : S155FT
3. Serial No : G024V02365N
4. Fault code : 552752-4
5. forklift condition : Noise at inside transmission
524230-4 – Rear Work Lights Relay (RL7) Driver Output OORL
A. SHORTED RELAY COIL
B. SHORT TO GROUND ON PDM RELAY DRIVER OUTPUT
C. FUNCTIONAL FAILURE IN CONTROLLER
I have a code 100-3 that won’t appear in the error code list any idea?
100-3 Engine Oil Pressure OORH
Good afternoon! I have a Tider FG-25 that is flashing 520260-0 and 4236-1. Wondering if you might be able to tell me what those codes are?
Thanks,
Shoup
I have a hyster h60ft with code 522660-0 don’t know what is and how to repair. Help
DTC 522660-0 – Long Term Closed Loop Correction Bank 1 Less Than NOR -35% (Rich Engine Operation)
POSSIBLE CAUSE
A. PROBLEMS THAT MAY CAUSE LEAN ENGINE OPERATION
B. PROBLEMS THAT MAY CAUSE RICH ENGINE OPERATION
C. SENSOR FAILURE
D. FUNCTIONAL FAILURE IN CONTROLLER
Tengo un código 524213_1 en un Hyster S60FT y no aparece en la lista
DTC 524213-1 – Horn Alarm Output Driver OC
POSSIBLE CAUSE
A. HORN OUTPUT DRIVER SHORT TO BATTERY
B. HORN OUTPUT DRIVER SHORT TO GROUND
C. HORN OUTPUT DRIVER OPEN CIRCUIT / HORN +VE SUPPLY OPEN CIRCUIT
D. FUNCTIONAL FAILURE IN CONTROLLER
Hola el código c019 no aparece en la lista
Buena noches tengo este código de error
Errd000 es un montacarga Yale GLP050MX
Buena tarde aparece un código 522752-9 pero en la lista no aparece gracias
DTC 522752-9 – Cam Sensor No Signal
POSSIBLE CAUSE
A. SENSOR SUPPLY/SENSOR GROUND OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL WIRE SHORTED TO GROUND
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Mam kod 524265 – 2 no trans braking. Co to oznacza?
DTC 524265-2 – TOSS Sensor 2 No Output
POSSIBLE CAUSE
A. SENSOR SUPPLY/GROUND OPEN CIRCUIT
B. SENSOR SIGNAL(S) OPEN CIRCUIT
C. SENSOR SIGNAL(S) SHORT TO GROUND
D. SENSOR SIGNAL(S) SHORTED TO +5VDC OR BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
I have a 360 hyster with code e0202 what is that
523253-12 hyster 155 code
523253-12: Lever 3 Position Data Invalid, Mini-Lever for lifting is maybe out of service
fault code524224 3truck disabled
DTC 524224-3 – Transmission Forward 2 Pressure OORH
POSSIBLE CAUSE
A. SENSOR GROUND OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT FAP, (HYDRAULIC PRESSURE AND MAZDA OIL PRESSURE ONLY)
C. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY
D. SENSOR SIGNAL SHORTED TO BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Que significa el error 12810
Please take the time to review the comments I made on November 19, 2020
Hyster H3.0ft fault code 523859-4
Please advise
Hi,
If you search in the previous comments, this complete code is explained
I have a code 524225-0
Please check the above Table
522713-3 how to error code in forclift
DTC 522713-3 – Accelerator B Position Sensor OORH
POSSIBLE CAUSE
A. ACCELERATOR PEDAL POSITION SENSOR SUPPLY OPEN CIRCUIT
B. ACCELERATOR PEDAL POSITION SENSOR SIGNAL SHORTED TO BATTERY SOURCE
C. ACCELERATOR PEDAL POSITION SENSOR SIGNAL SHORTED TO SENSOR SUPPLY
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Fault 190-7 skáče mi tam chyba každý den skoro 20* jezdí servis kvůli tomu ale neví si rady neví te co stim jé??
DTC 190-7 – Engine Speed Exceeds Command
POSSIBLE CAUSE
A. OPEN CIRCUIT IN SENSOR SUPPLY
B. SENSOR SIGNAL OPEN CIRCUIT OR SHORT TO GROUND
C. SENSOR SIGNAL SHORTED TO BATTERY SOURCE
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
I have the following fault code. On Hyster 100ft.
2000-12
CAN Tx Failure
A. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO B. CAN HI AND CAN LO SHORTED TOGETHER C. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES D. STG ON CAN HI E. STS/STB ON CAN LO F. CAN CONNECTED DEVICE FAILURE
2000-12
CAN Rx Failure
Not sure what this means or where to start
COMPONENT OPERATIONAL CHECK
PROCEDURE OR ACTION:
1. Turn power to OFF for no less than 30 seconds, and then to ON to clear displayed DTC.
Does reported DTC reoccur?
YES: Go to Step 2.
NO: Problem not verified. Resume operation.
2. Conduct a quick visual inspection of all connectors/wiring associated with the displayed fault code.
Are any faults detected/observed?
YES: Repair/replace connector or wiring associated with faults found. See Electrical System 2200 SRM 1142
Defaut 93-3 et 94-3 hyster 3 gazoil
Hello, we have several error codes and our Hyster S60FT (Serial Number: F187V04786C) won’t start!
VSM 524263-1
ECU 106-14
VSM 168-4
VSM 522801-13
Thanks for your help!
DTC 524263-1 – Uncommanded Power Down
WARNING
For DTC 524263-1 – DO NOT REPLACE VSM for this fault code. Complete Component Operational Check
and Clear VSM Fault Log.
POSSIBLE CAUSE
A. TCU PROGRAM CORRUPTED OR TCU APPLICATION FILE MISMATCH
B. FUNCTIONAL FAILURE IN CONTROLLER
DTC 106-14 – MAP Sensor While Cranking, Not Different From Atmospheric Pressure
POSSIBLE CAUSE
A. SENSOR FAILURE
B. FUNCTIONAL FAILURE IN CONTROLLER
DTC 168-4 – System Battery Voltage OORL
POSSIBLE CAUSE
A. BATTERY FAILURE
B. ALTERNATOR FAILURE
C. OPERATION CYCLE TOO SHORT TO CHARGE BATTERY
D. QUIESCENT CURRENT DRAW TOO HIGH DURING TRUCK OFF TIME
DTC 522800-13 Transmission Valve Calibration
POSSIBLE CAUSE
A. TRANSMISSION VALVE CALIBRATION REQUIRED
B. NEW TCU PROGRAM REQUIRED
C. FUNCTIONAL FAILURE IN CONTROLLER
Can you tell me what these codes are?
523580-2
522326-2
Merhaba 2236_12 ariza kod var kontaktan calismiyo levyeler ve ileri geri yok
DTC 2236-12 – CANbus Comm Error With MLM
POSSIBLE CAUSE
A. TERMINATION RESISTOR(S) OPEN CIRCUIT
B. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO
C. CAN HI AND CAN LO SHORTED TOGETHER
D. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES
E. STG ON CAN HI
F. STS/STB ON CAN LO
G. CAN CONNECTED DEVICE FAILURE
It’s throwing code # 523602-0 no power. Says no code found. What do I do ?
Forklift model -ERP20VT Yale forklift
FAULT CODE -65513
Hello I have a fault with the number 523930-4, it goes into error when I give it forward or backward, can you help me?
DTC 523930-4 – Clutch FWD1/Return Circuit OORL
POSSIBLE CAUSE
A. COIL DRIVER/DRIVER RETURN SHORTED TO GROUND
B. FUNCTIONAL VALVE FAILURE
C. FUNCTIONAL FAILURE IN THE CONTROLLER
MomCode 880-4
J’ai le code défaut 522772-3
DTC 522772-3 – Backup Lamp Driver Output OORH
POSSIBLE CAUSE
A. LAMP DRIVER OUTPUT SHORTED TO BATTERY
B. INTERMITTENT SHORT OR OTHER POWER SOURCES
C. FUNCTIONAL FAILURE IN CONTROLLE
Fault 522800-13 its not on the lust
DTC 522800-13: Transmission Valve Calibration
POSSIBLE CAUSE
A. TRANSMISSION VALVE CALIBRATION REQUIRED
B. NEW TCU PROGRAM REQUIRED
C. FUNCTIONAL FAILURE IN CONTROLLE
I have E0559, any idea what does that code means, or is it even a code?
code is injector metering pressure reading low rail 1 (moderate)
Can be the problem in a quick connection hose just before the fuel pump
C028 what the heck is this code!?
anyone know what code 88-2 is on a S35Ft fortis
yale fork lift XNYLE084 S# C875V01780M need to know what the symbols located on dash are when alerted
What’s on the Yale 80vx. It’s showing the code 723-8.
Hello
We have a Hyster H35TX-2L serial B466R04937E forklift
Error code 19
Would you be able to advise what this is?
Much appreciated & thank you for your help
I have a Yale GDP300 with tc E-0197 and E-0235 coming up and it randomly shuts down. Any ideas?
Ryan, did you ever get any feedback on this? i have the same fault codes and symptom.
Hello
We have a Hyster H35TX-2L serial B466R04937E forklift
Error code 19
Would you be able to advise what this is?
Much appreciated
I have a 2009 YALE Forklift
YALE GLP050VXNVSE086 Serial # B875V02973G
Showing a fault code 522760-4
This fault is locking out the lifting, tilt and side shifting controls
This fault code is not on your list, how do I get my lift useable again?
I had a local service technician come out and he was unable to find the problem.
DTC 522760-4 – Switched Battery Voltage 1 (IGN 1) OORL
A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY
B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND
C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND
D. FUNCTIONAL FAILURE IN CONTROLLER
we update the table too
I have a yell ERCO 30 VAN 36TE0 82 code 12833 what does that mean
You can check for the voltage drop across the line contactor. This code indicates that the controller is seeing the battery voltage below the set minimum.
Hello I have a Hyster serial# f001vo3166f. Forklift keeps throwing code 522593 – 12. The code says communication lost to ECU to EPR. What would cause such a problem?
DTC 522593-12
EPR Communication Loss
POSSIBLE CAUSE
A. EPR SUPPLY/GROUND OPEN CIRCUIT
B. CAN HI OR CAN LO OPEN CIRCUIT
C. CAN HI SHORTED TO GROUND
D. CAN LO SHORTED TO UNSWITCHED OR SWITCHED BATT +
E. EPR FAILURE
Greetings
I have Yale ERP-030TGN ,serial E807N01849X, forklift showing error code 09578.
Can you help with this?
Thank you
hyster 80 fortis code 1271-5 ?
Spark Coil #4 Primary
I have errors 676-4 code what means
DTC 676-4 – Glow Plug Relay Driver Output OORL
POSSIBLE CAUSE
A. COIL DRIVER OUTPUT SHORTED TO GROUND
B. RELAY/VALVE COIL/ FAILURE
C. FUNCTIONAL FAILURE IN CONTROLLER
Yale forklift 2000-12 dont start , fuelpump solonoind no power and electric fuelpump get no voltage .
I think the ecu needs to feed those items but how can i search whats wrong ?
Did you get any code on the dash?
H100ft fault code 2000-31 can anyone tell me what this code is
Does anyone have a clue on a heister 60 forklift code 102-4 is
Intake Manifold Pressure Sensor Circuit – Voltage Below Normal, or Shorted to
Low Source
Hello,
Our Hyster forklift is showing fault code Fault 522760-4.
What could that be.
Regards
J Mennen
The error code is exist in table above
Hello I have hyster forklift 3.0 xt
Err code 000 how do I solve
Error code 150 displayed on J1.75EX 1.8T Hyster/Yale forklift. Any ideas as can’t seem to find fault listed anywhere??
I have one Hyster and the code is 2000-12 don’t start the engine for You atention thanks
DTC 2000-12 – CANbus Comm Error VSM
DTC 2000-12 – CANbus Errors (Mazda ECU)
DTC 2000-12 – CAN Tx Failure
DTC 2000-12 – CAN Rx Failure
POSSIBLE CAUSE
A. TERMINATION RESISTOR(S) OPEN CIRCUIT
B. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO
C. CAN HI AND CAN LO SHORTED TOGETHER
D. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES
E. STG ON CAN HI
F. STS/STB ON CAN LO
G. CAN CONNECTED DEVICE FAILURE
Have hyster 360-48 error 0132 has no throttle only creep mode. May have runner it without def.
Can be from Accelerator Pedal or Lever Position Sensor 1 Circuit – Voltage Below
Normal or Shorted to Low Source.
Hi
Hyster H60FT has a fault code 523920-3. I did not see it on the table. Any help is greatly appreciated.
Hi,
there is in table otherwise :
Diagnostic Codes:
REV Circuit Shorted High,
Possible Cases:
A. COIL DRIVER OUTPUT SHORTED TO SYSTEM VOLTAGE
B. COIL SHORT CIRCUIT
C. FUNCTIONAL FAILURE IN CONTROLLER
Have a hyster n40xmr2 a470. Codes 063. 065 come on
Hello,
I am in the US Air Force and we have a hyster forklift model J50XN-28 and I am having fault code 8976 and the vehicle shuts down. I can’t find any sources to dial in the issue and was wondering if you could help me out. Thanks in advance.
thanks for giving these codes
HI! Yale ERP16VFMWBE seria A955B01546G error code 12576???please
DTC 12576
Motor Voltage Not OK
you have open in the motor circuit or bad motor controller or bad wiring to the motor controller from the motor.
Thank you very much for your help in getting your forklift good!Maria
I have fault code 524 261_1 no drive can you help
TSP 5 Volt Supply OORL
DTC 524260-1 – 5 Volt Supply Circuit B OORL
DTC 524261-1 – 5 Volt Supply Circuit A OORL
POSSIBLE CAUSE
A. 5 VOLT “A” SHORTED TO GROUND
B. 5 VOLT “B” SHORTED TO GROUND
C. 5 VOLT “C” SHORTED TO GROUND
D. VSM FAILURE
E. 5 VOLT ECU POWER SUPPLY SHORTED TO GROUND
Hyster h50xt fault code ERRE649
Hyster 50 fault code 100-2 Any ideas would be greatly appreciated.
DTC 100-2 – Engine Oil Pressure OORH at Stall, Go to Cause D
DTC 100-2 – Cummins-Code 435. See QSB 3.3L Troubleshooting and Repair
POSSIBLE CAUSE
A. SENSOR GROUND OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT FAP, (HYDRAULIC PRESSURE AND MAZDA OIL PRESSURE ONLY)
C. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY
D. SENSOR SIGNAL SHORTED TO BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
hello, where you able to figure out the issue. having the same fault code.
524223-4
merci DE TROUVE UN SOliSTIoN
The table above was updated
Hi im getting fault code 522735-5 on my hyster H90FT forklift
Moddel # P005V02908H
Cant seem to find the code anywhere please help
DTC 522735-5 – Oxygen (O2) Sensor Signal Open Circuit
DTC 522736-5 – Oxygen (O2) Sensor Signal Open Circuit
POSSIBLE CAUSE
A. SENSOR SIGNAL OPEN CIRCUIT
Hey I’m getting 177-3 code coming up PLS help
DTC 177-3 – Transmission Oil Temperature Sensor OORH
POSSIBLE CAUSE
A. SENSOR RETURN OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO 5V OR BATTERY VOLTAGE
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Fault 522138-1 hyster 7 tun
DTC 522138-1 – Intermediate Shaft Speed Sensor Pulse Count Too Low (TCU)
POSSIBLE CAUSE
A. SENSOR IS NOT FULLY INSTALLED IN THE MOUNTING HOLE AND SECURED
B. SENSOR SUPPLY IS OPEN CIRCUIT
C. SENSOR FAILURE
D. FUNCTIONAL FAILURE – MECHANICAL
Sir fault 59 indicate….and forklift machine are verry slow ly running when fault indicate
I changed out the computer and plugged the battery back up and it constantly says 12810 with a flashing wrench
Accelerator pedal position out of range low.
Check the connector at the pedal assembly.
The plug is disconnected
What is the problem when a 2001 hyster h5.50xm with a perkins diesel displays code 15?
Hi Van Yale ERP-16VFMWBE2130, serial A955B01546G, forklift speed adjustment / speed increase
Could you help with this? 🙏
Thanks
Code 76
Model erc050ghn48te088
Yale pallet lift EP 107
Any help would be greatly appreciated
Yale .error code is 2003-12
Any ideas ? :)
2003-12 : CANbus Error With TCU
Problem with the Canbus signal to the transmission controller. Check for opens and shorts.
Hey I have a code 2000-12 no start and intermittent spark can you put me in the right direction and where to start
possible causes:
termination resistors open circuit
open circuit on can hi, can lo
can hi and can lo shorted together
open circuit on power/ground to can connected devices
stg on can hi
sts/stb on can lo
can connected device failure
Hola, Tengo un montacargas H120FT, el cual presenta el siguiente código de falla: 2350-3Engine Shutdown
Mucho sabría agradecer su valiosa ayuda al respecto, Saludos, Feliz día
DTC 2350-3 – Front Work Lights Relay (RL4) Driver Output OORH
POSSIBLE CAUSE
A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED
B. SHORT ON RELAY DRIVER OUTPUT TO UNSWITCHED BATTERY (SEE WARNING BEFORE CONTINUING)
C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY.
D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE
E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT
F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT
G. FUNCTIONAL FAILURE IN CONTROLLER
HYSTER MODEL 2001 SN F007E01579Y ERR 32 IN DASCHBORD CAN YOU HELP ME
Main tips are welded or the main contactor driver is shorted
what does code 522800-13 refer to
522800-13: Transmission Valve Calibration
check and calibration Valve
51-7 yale
DTC 51-7 – Throttle Position Sensor Signals A and B Not At Commanded Value
POSSIBLE CAUSE
A. ELECTRONIC THROTTLE BODY STICKY
B. THROTTLE MECHANISM INCORRECTLY ADJUSTED
C. SENSOR (THROTTLE BODY) FAILURE
D. SENSOR SIGNAL CIRCUIT HIGH RESISTANCE (MAZDA ONLY)
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Code 522760-3?
We update the above table please check it!
Hello evry body i have a problem at a hyster j1.8cmt year 2003
Error codes: 275; 69 and 266 juste the steerring pompe work
I change all shunt off batry
Guten Abend,
Wir besitzen einen Yale MS 15 x, beim einschalten zeigt er den Fehlercode 21552.Der Hochhubstabler
fährt und der Freihub funktioniert aber der Hubmast fährt nicht hoch.Könnten Sie mir helfen? Wenn die Stecker für den Hubmast beim Start von der Platine abgezogen werden, zeigt sie keinen Fehlercode an, wenn Sie dann aufgesteckt werden kommt der Fehler 29457.
Mit freundlichen Grüßen B..y
Hello I have a Hyster H90FT the error code I keep receiving is 157-1 and I lose power in the lift
Hello,
157-1: Rail Pressure Too Low
The Motor Control Module (MCM) monitors the rail pressure and when rail pressure deviation is greater than 200 bar for eight seconds, the MCM sets the code. This fault can occur due to the conditions listed below:
External fuel leakage between the high-pressure pump and fuel injectors
Pressure limiting valve leakage (internal)
Fuel filter integrity (loose caps, plugged filters)
Fuel supply issues (fuel level, fuel aeration, leaking fuel lines, fuel restrictions)
Intermittent loss of engine speed signal
High pressure pump internal failure
Fuel injector (amplifier or needle) leakage
Fuel Contamination
Rail pressure sensor
Motor Control Module (MCM)
HI Does anyone know what fault is code 12800 on Yale(ERP16Vt) forklift ?
Thank you.
Hi, I have a erp16VT Yale forklift and it is not starting, it is coming up with the fault code 12800. Do you know what this fault code means?
Thanks.
We have a error code 522636-4
Yale forklift
Model # glp050vxegse084
Thank you
Pre-Cat Bank 1 Short Term Fuel Correction Railed Rich
Eror code 19 pada forklift yale apa?
Hyster 9.00 codice guasto 3516-18
È capitato a qualcuno?Come avete risolto? grazie
I have a Hyster j40z with a code 207 dose anybody know what this code is??
I need to know how to reset the password. Hyster h50ft. Code is not 55555 or the last digits of the serial number. I only have 7 tries before it locks me out. It’s been unhooked from a battery for two months. I’m trying to erase the codes. I have a couple. Trans temp sensor problem and map sensor problem.
Hi,
We have an Error Code 12804 in our Hyster J30XN, need to know how to rectify.
Thanks.
The VSM is seeing 2 directional inputs at the same time. Check the wiring at the VSM connector. If it is OK, you probably have a defective VSM or it needs to be reflashed. Check to see that there is a static strap on the truck.
have a hyster with gm 2.4 code 522630-2 runs like crap cold worms up and runs mint can’t find anything on code ?
522630-2 Pre-Cat Bank 1 Sensor Fails To Switch To Lean
hi – I’m getting a 00215 status code on my yale forklift.
thanks!
Hello i have an hyster reach truck with this error 250-33
PLEASE HELP!!!
Hi Forklift plus and the rest of the world
Our Yale electric forklift displays error 226 and will only move half a metre before stopping. We believe it’s the auto brake when you lift your foot off the accelerator.
Repair guys want $12,000 for a new control unit. Can you help us with an exact cause and remedy. Stay safe out there
yale 80VX forklift with code 723-8
Hello, my Yale GLP050VX shows error 168-4, what is this code?
DTC 168-4 – System Battery Voltage OORL
POSSIBLE CAUSE
A. BATTERY FAILURE
B. ALTERNATOR FAILURE
C. OPERATION CYCLE TOO SHORT TO CHARGE BATTERY
D. QUIESCENT CURRENT DRAW TOO HIGH DURING TRUCK OFF TIME
Hello my hyster modele j2.0xn lwb
Serie A935B03507L
Error 12592 what isthis code ?
code 12592: Check all the wiring to the solenoids. node 3/4/5 is because there is a drain on the system with coils shorted, so the precharge on the controller capacitor is low.
Hello my hyster modele j2.0xn lwb
Serie A935B03507L
Error 21792 with this error
Hello my hyster modele j2.0xn lwb
Serie A935B03507L
Error 65792 with this error
hi I’m looking for code 523524-4 please and thanks
Common 2 Actuation Shorted To Ground
Im getting a Code not on the lost
522810-4
DTC 522810-4
Alternator Charge Excitation Signal OORL
Alternator Excitation Signal Is Below Allowable Threshold
POSSIBLE CAUSE
A. EXCITATION SIGNAL SHORTED TO GROUND
B. EXCITATION SIGNAL OPEN CIRCUIT
C. PDM FUNCTIONAL FAILURE
D. FUNCTIONAL FAILURE IN CONTROLLER
hi all, we have a forklift yale
Marca: YALE
MODELO: GLC050VXNVSE094
Serie: A910V062290
have a 677-3 code and dont start
can you help us
thanks
DTC 677-3 – Starter Relay (RL5) Driver Output OORH
DTC 2350-3 – Front Work Lights Relay (RL4) Driver Output OORH
DTC 522754-3 – Fuel Pump Relay (RL2) Driver Output OORH
DTC 522755-3 – Back Up Alarm Relay (RL3) Driver Output OORH
DTC 522764-3 – Ignition 1 Relay (RL6) Driver Output OORH
DTC 522766-3 – Ignition 3 Relay (RL1) Driver Output OORH
DTC 524230-3 – Rear Work Lights Relay (RL7) Driver Output OORH
POSSIBLE CAUSE
A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED
B. SHORT ON RELAY DRIVER OUTPUT TO UNSWITCHED BATTERY (SEE WARNING BEFORE CONTINUING)
C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY.
D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE
E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT
F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT
G. FUNCTIONAL FAILURE IN CONTROLLER
I have 190-11,2634-5,652-5 ,,, plas help,,, forklift lonking..
i have a hyster h50ct with a error 520300-14 and cant find it anywere
I have a hysterectomy E60Z-33 with an error code 52. Can someone tell me what the problem is?
Sorry. Hyster model E60Z-33
Hyster Fortis 155 forklift throwing code 522126-8. Truck will say disabled or function reduced. What is this from?
DTC 522126-8 – Transmission REV1 Valve Current Out Of Range (TCU)
POSSIBLE CAUSE
A. HIGH RESISTIVE CONNECTION
B. VALVE -VE SHORTED TO BATTERY – VE/FRAME GROUND
C. FUNCTIONAL FAILURE IN CONTROLLER
Hi sir.my heli 180 forklift for backward is not moving.whats the possible cause of this problem?
522660 0
DTC 522660-0 – Long Term Closed Loop Correction Bank 1 Less Than NOR -35% (Rich Engine Operation)
POSSIBLE CAUSE
A. PROBLEMS THAT MAY CAUSE LEAN ENGINE OPERATION
B. PROBLEMS THAT MAY CAUSE RICH ENGINE OPERATION
C. SENSOR FAILURE
D. FUNCTIONAL FAILURE IN CONTROLLER
hi
good morning
yale lift truck model ERP30VL E2145
ERROR CODE 33025 TROUBLE
CAN YOU HELP ANY
I have an S155FT ser#G024V prefix. I have a code 3271-4. Motor will turn over but not start . I have fire at the coil and plugs. DTC not in code book. Thanks
Hello,
I have a Yale Model 30VX showing error code 524265-2
Can you help me out?
Thanks in advance!
CODES
DTC 524250-14 – TOSS/TISS Special Conditions
DTC 524264-2 – TOSS Sensor 1 No Output
DTC 524264-14 – TOSS/TISS Special Conditions
DTC 524265-2 – TOSS Sensor 2 No Output
DTC 524271-2 – TISS Sensor Pulse Count Low
DTC 524225-14 – TOSS Sensor Dual Output Failure
POSSIBLE CAUSE
A. SENSOR SUPPLY/GROUND OPEN CIRCUIT
B. SENSOR SIGNAL(S) OPEN CIRCUIT
C. SENSOR SIGNAL(S) SHORT TO GROUND
D. SENSOR SIGNAL(S) SHORTED TO +5VDC OR BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
I HAVE A HYSTER LIFT SERIAL #F001V03867J. ITS GIVING CODE 168-3 DO YOU HAVE ANY IDEAS WHAT THIS CODE IS?
DTC 168-3 – System Battery Voltage OORH
POSSIBLE CAUSE
A. ALTERNATOR FAILURE
B. FUNCTIONAL FAILURE IN CONTROLLER
I have a 2010 hyster H155ft Serial number J0067G02622h. Its throwing a 524240-4 code, which i found was the washer pump drive command OORL. Curious to see if anyone else has had this issue and what this fix was. Thanks
DTC 524240-4 – Washer Pump Drive Command OORL
POSSIBLE CAUSE
A. PARK SWITCH STUCK OPEN (DTC 524237 OR 524238 ONLY)
B. MOTOR/PUMP/DRIVE OUTPUT SHORTED TO GROUND
C. SUSTAIN DRIVE SUPPLY FAILURE/OPEN CIRCUIT
D. IGNITION 1 CAB RELAY DEFECTIVE
E. PUMP/DEVICE FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
NOTE
Please refer to the end of this procedure for supporting diagrams.
COMPONENT OPERATIONAL CHECK
PROCEDURE OR ACTION:
1. Turn power to OFF for no less than 30 seconds, and then to ON to clear displayed DTC.
Does reported DTC reoccur?
YES: Go to Step 2.
NO: Problem not verified. Resume operation.
2. Conduct a quick visual inspection of all connectors/wiring associated with the displayed fault code.
Are any faults detected/observed?
YES: Repair/replace connector or wiring associated with faults found.
Hyster J30NXT Flasing wrench and code above is 64974
Hi! i have hyster model R1.4 showing code 227-01 what could be the problem?
Hi, help me please)
Hyster J1.50XNT K160B04546K showing code 12576 what could be the problem?
DTC 12576
Motor Voltage Not OK
DC Bus charging timeout.(Usually caused by low battery voltage or poor connection.) you can open in motor circuit or bad motor controller or bad wiring to motor controller from motor
mi equipo es yale, marca erro 12818 podrían apoyarme que significa ese error
Hi , I need help
Hyster H3.0Ft MY 2007
CODE 522781-3 where is the problem ?
DTC 522781-3 – MONOTROL® REV Switch OORH
POSSIBLE CAUSE
A. MONOTROL® SWITCH OPEN CIRCUIT
B. MONOTROL® SWITCH SIGNAL SHORTED TO SUPPLY VOLTAGE
C. MONOTROL® SWITCH SIGNAL SHORTED TO BATTERY SOURCE
D. MONOTROL® SWITCH FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Hi! I have a forklift Yale 20glp with error 100-4. Forklift starts/runs but the loader mast lift control does not work. Thanks:)
DTC 100-4 – Engine Oil Pressure OORL
POSSIBLE CAUSE
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Hi, 2005 Hyster Yale Electric forklift J2.00HEX error code 184
Thanks.
Hyster Fortis 60
Fault Code 524261-4
What is causing the fault code?
DTC 524261-4 – 5VE1 Sensor Supply Circuit Voltage OORL (Mazda)
POSSIBLE CAUSE
A. 5 VOLT “A” SHORTED TO GROUND
B. 5 VOLT “B” SHORTED TO GROUND
C. 5 VOLT “C” SHORTED TO GROUND
D. VSM FAILURE
E. 5 VOLT POWER SUPPLY SHORTED TO GROUND
F. FUNCTIONAL FAILURE IN CONTROLLER
I have a code on a Yale MSW040SFN24TV087 the code on the screen shows a wrench and AL-06. None of the functions work, when the machine is first turned on it shows no codes until you try to operate it and just clicks and pops up a red light with the cod on the screen. Any info helps
Error: AL06
What the issue is: Traction and hydraulic functions not working
Cause of Problem: Damaged connection to traction motor; traction motor armature resistance is too low; field wires are loose or damaged; motor field winding is shorted or too low.
What to Do: Check the electrical connection between traction motor, field wires, and controller; check traction motor armature for shorts; check motor field resistance and correct if not between 0.5 and 1.5 ohms; check contactor coil for resistance of 52 ohms
I have a code of 522125-8 . I don’t see it in the table of codes
Table updated
Hi, I have error codes 30, 35 and 39 come up on a Yale GD280DB could you tell me the faults.
Thanks Mike
Fault: 676-3.
Hard start intermittent
Goes to engine shutdown mode
Please check the table
Yale GPD20SVX
Fault 676-4 what ist This?
DTC 676-4 – Glow Plug Relay Driver Output OORL
POSSIBLE CAUSE
A. COIL DRIVER OUTPUT SHORTED TO GROUND
B. RELAY/VALVE COIL/ FAILURE
C. FUNCTIONAL FAILURE IN CONTROLLER
błąd 522772-4 Wyjście sterownika lampy zapasowej OORL – co to jest OORL – jak skasować błąd , czy zniknie sam po usunięciu usterki ?
The table above was updated
Anyone know the problem for ErrE649
I have a Hyster 360. codes came up E0197 & E0235 Can someone tell me what these are
I have forklift yale veracitor 120 VX serial G813VO1958G crank but no star only on the screen show code 524245 -3 and 3237 the first one is seat sensor i can’t find 3237
POSSIBLE CAUSE
A. SENSOR GROUND OPEN CIRCUIT
B. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY
C. SENSOR SIGNAL SHORTED TO BATTERY
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLE
The forklift show diferent code when switch on and a wrench in the screen . The code is 33025 and 21820.
Forklift yale..
Yale pallet jack Model: MPB045VGN24T2746
Display says “Maintenance Required”. Checked batteries, low on water, filled up battery water. Hydraulic oil reservoir is full. Fully charged. Still has the same message. Drives and lifts no problem.
Yale GP050
Fault Code 522760-10
What is causing the fault code?
I have a Yale ERP20ATF from the year 2003 and it has error 68 and error 223. Can you help me please?
2005 Hyster S30Ft 4cylinder propane shows “Fault 108-1” which from search seems to be a barometric pressure too low and possible fixes all seem to be sensor faults. What does this fault really mean and could it be a minor or could it be a significant repair issue?
DTC 108-1 – Barometric Pressure Below Acceptable Limit
POSSIBLE CAUSE
A. SENSOR FAILURE
B. FUNCTIONAL FAILURE IN C
Hello
I have a hyster Forklift R1.4 , when starting up , i receive the following message on the display – Alarm on MOD 09 driver shorted & the forks will not operate
Can you advise
regards
Hello.
I have a Hyster 2.5 Fortens forklift with automatic transmission. It is presenting the code 524223-4. When I put on a leash it doesn’t move forward or backward.
Help guys.
DTC 524223-4 – Transmission Reverse Pressure OORL
DTC 524224-4 – Transmission Forward 2 Pressure OORL
DTC 524225-4 – Transmission Forward 1 Pressure OORL
DTC 524282-4 – Hydraulic Lift (Load Weigh) Pressure OORL
POSSIBLE CAUSE
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
hi I have a Hyster 3.0xt, serial number D466R06228s. The following code appears on the dash monitor, ErrC013. Machine functions fine. please assist.
Hi I have a hyster 3.0 Fortens 2007 with error codes 523859-4 and 879-4. Truck currently has no drive in either forward or reverse. There is currently no brake lights or indicators either. Thank you
DTC 523859-4 – Service Brake Pressure OORL
POSSIBLE CAUSE:
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
DTC 879-4 – Left Turn Lamp Driver Output OORL
POSSIBLE CAUSE:
A. LAMP DRIVER OUTPUT SHORTED TO GROUND
B. FUNCTIONAL FAILURE IN CONTROLLER
Hyster j1.6nx error code 21569. Help, please. Thank you
Hi,
The fault is line contactor open.
Code 654-3 for Yale Kubota engine. Don’t know what this code means.
DTC 654-3 – GM Gas Drive Injector 4 Shorted To B+
POSSIBLE CAUSE
A. INJECTOR CIRCUIT SHORTED TO BATTERY SOURCE
B. INJECTOR DRIVER MODULE FAILURE
C. FUNCTIONAL FAILURE IN CONTROLLER
i have a fortis hyster 2012 brings up code 4184 does anyone know what it is
Hi my hyster electric Jack lift shows error code of 14602 any one help me to find out the error Please….
2000-12 kubota 3800 diesel year 2015 wont start and diagnose program tell me “bad intelligence device” what could i do ? Im mechanic
hi there i have a Hyster H8XM-6 with a E0131 fault code.
looking to see if anyone code point me in a direction of what to check the fault is.
thanks
Yale electric Counter balance Serial number= G807N11945S ERROR CODE 33029
The code can indicate a loss of communication between the system manager and the pump controller through the CANBUS.
Check your connectors at the VSM and the hydraulic controller.
The wires you need to check are the green/ yellow twisted pair. There could be a failure in one of the controllers also
hyster S80FT H004V01618K
CODES
523261-12
522760-4
DTC 522760-4 – Switched Battery Voltage 1 (IGN 1) OORL
POSSIBLE CAUSE
A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY
B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND
C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND
D. FUNCTIONAL FAILURE IN CONTROLLER
Code 32062 shows up on my yale ride on what does this code means
Hyster Type H8.OFT6. Serienumber A299E01694K.
Code 627-2
Power Lost without Ignition Off – Data Erratic, Intermittent, or Incorrect
Hyster E1.50 Hm error code displey 65 and 16
Hi I have a hyster p.20 pallet jack with error code 39 have replaced the emergency stop and all wiring looks good what could be causing this?
Change wiring harness inside handle from tiller to DUETZ plug near controller will fix this fault and also sometimes the sensor as well
523261-12 level 1 position data invalid. whats the cause and way to fix?
Forklift Serial # U005V03810P. Forks wont go up or down. Finger Switch is good.
I have a yale ERP030-040VF fault code 12836? Can’t seem to find anything on it
DTC 12836 – Service Brake Pressure
DTC 12836 – Brake Pedal Sensor A OORL
Hello I have Code 523859-3 cant seem to find it, any help would be awesome!
DTC 523859-3 – Service Brake Pressure OORH
POSSIBLE CAUSE
A. SENSOR GROUND OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT FAP, (HYDRAULIC PRESSURE AND MAZDA OIL PRESSURE ONLY)
C. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY
D. SENSOR SIGNAL SHORTED TO BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
We are facing Fault 881-4 .
Forklift starting but after few minute later its stopping.
Please help to resolve issue.
What to be check?
DTC 881-4 – Right Turn Lamp Driver Output OORL
POSSIBLE CAUSE
A. LAMP DRIVER OUTPUT SHORTED TO GROUND
B. FUNCTIONAL FAILURE IN CONTROLLER
Sztaplarka YALE
Model GDP 25 VX V2170
Rok produkcji 2007
Błąd 524264-14
Za co odpowiedzialny jest ten błąd?
DTC 524264-14 – TOSS/TISS Special Conditions
POSSIBLE CAUSE
A. SENSOR SUPPLY/GROUND OPEN CIRCUIT
B. SENSOR SIGNAL(S) OPEN CIRCUIT
C. SENSOR SIGNAL(S) SHORT TO GROUND
D. SENSOR SIGNAL(S) SHORTED TO +5VDC OR BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Yale glc050 fault code:
524246-4
I’m finding nothing anywhere we look. Any help would be appreciated. Thanks in advance…
I am looking for information on code E0323 on a Hyster fork truck.
helo,
1. maker : hyster
2. Serial No : G108A02941G
3. Fault code :
44 when I turned the key,disappears after a minute.
sometimes the lift stops and code 53 54 blinks
I’m finding nothing anywhere we look. Any help would be appreciated. Thanks in advance…
Hello, Good after noon from UAE,
Model No Hyster H16.00XM 6
I have an error code
E0428
E5304
Kindly Explain the error code,here the technicians getting trouble regard with it
Hi,
for E0428: can be Water in Fuel Indicator Sensor Circuit – Voltage Above Normal or Shorted to High Source
hello,
Many thanks for your reply,now i am receiving an error codes from yesterday kindly explain,
Error codes
E 2249
E 1117
E 0559
Waiting for your response,
many thanks in advance.
E 1117 Power Supply Lost With Ignition On – Data Erratic, Intermittent, or Incorrect
E 0599 Auxiliary Commanded Dual Output Shutdown – Special Instructions
These are both losses of ignition with the key on.
Hello, I have hyster R 1.6 electric error code 250 -33 and 211-02 , any idea on these errors codes please
Many thanks in advance
Error code 250-33 refers to a fault with the truck’s accelerator pedal position sensor.
This sensor is responsible for communicating the position of the accelerator pedal to the truck’s electronic control module (ECM).
A fault with this sensor can cause the truck to operate incorrectly or not operate at all.
Error code 211-02 refers to a fault with the truck’s hydraulic system.
Specifically, this code indicates that the truck’s hydraulic pressure is too low.
This can be caused by a number of factors, including low hydraulic fluid levels, a faulty hydraulic pump, or a problem with the hydraulic system’s pressure regulator.
DID YOU EVER FIGURE OUT WHAT E2249 AND E0559 WAS?
The E2249 and E0559 error codes are specific to Hyster and Yale forklifts and are related to the hydraulic system. Here is a brief explanation of each error code:
E2249: This error code indicates an issue with the hydraulic system’s pressure sensor circuit. It is possible case: that the sensor is malfunctioning, the wiring is damaged or disconnected, or the hydraulic pressure is outside of the acceptable range.
This error may lead to a loss of hydraulic power, affecting the forklift’s ability to lift or move loads.
E0559: This error code indicates an issue with the hydraulic system’s solenoid valve circuit. It is possible case: that the solenoid valve is malfunctioning, the wiring is damaged or disconnected, or the hydraulic pressure is outside of the acceptable range. This error may lead to a loss of hydraulic power, affecting the forklift’s ability to lift or move loads.
que buena informacion muchas gracias alguien sabe del codigo 524223-0
YALE MODEL ERP030VTN36TE078 ERROR CODE 64974 Unit is in a walk in cooler and goes outside quite abit. Code comes up and unit shuts off. Thanks for all the help.
Have hyster H18 can i get some help with the meanings of these fault codes
E2555
E0272
E0221
MERHABA BENİM YALE FORKLİFTİM VAR GDP40VX5 V2171
SERİ NO:K813B02152R
BU ARIZA KODLARINI VERİYOR YARDIMCI OLURMUSUNUZ
132-4
100-4
523575-7
DTC 100-4 – Engine Oil Pressure OORL.
POSSIBLE CAUSE
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT (NOT VALID FOR OIL PRESSURE)
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
do you know what a hyster error code 12816 is?
check the wiring harness, operators are bad about cramming crap under and around seats and they almost always cut or damage wiring, or it just could be a bad seat switch.
we are using YALE make high reach for material movement. from last two days we are facing issue with 12592 error but i cant understand what is the issue. can yo u please explain how to sort out the issue.
Model No: ERP20VT MWB E-2130
S.No: G807B02542H
Hi. We have Yale model ERC065RGN36TE082 forklift that is throwing an error code of “67”. Verified that there is full range of motion in the fork, but forklift will not drive (no motion forward or backwards. Any help/advice would be appreciated. Thanks.
Hi,
I have error code 12592 and 65280 on my Hyster A1.5XNT SN: D203B01706L the truck has no drive currently.
Are you able to offer any help as to what these would be related to?
Thank you
Please advise on the forklift dash appears error code 51-7
What can the problem be
DTC 51-7 – Throttle Position Sensor Signals A and B Not At Commanded Value
POSSIBLE CAUSE
A. ELECTRONIC THROTTLE BODY STICKY
B. THROTTLE MECHANISM INCORRECTLY ADJUSTED
C. SENSOR (THROTTLE BODY) FAILURE
D. SENSOR SIGNAL CIRCUIT HIGH RESISTANCE (MAZDA ONLY)
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Hi I have error codes 157-18 and 522762-3 does anyone know what these codes are related to i am not finding any info
157-18 : Injector Metering Rail #1 Pressure Low – Data Valid but Below Normal Operational
Range -Moderately Severe Level
DTC 522762-3 – Switched Battery Voltage 3 (IGN 3) OORH
POSSIBLE CAUSE
A. IGN VOLTAGE SHORTED TO UNSWITCHED BATTERY SOURCE IN PDM OR PDM/VSM HARNESS
B. IGN VOLTAGE SHORTED TO UNSWITCHED BATTERY SOURCE IN PDM OUTPUT HARNESS
C. IGN VOLTAGE SHORTED TO SWITCHED BATTERY SOURCE IN PDM OR PDM/VSM HARNESS
D. IGN 2 VOLTAGE SHORTED TO BATTERY SOURCE
E. FUNCTIONAL FAILURE IN CONTROLLER
524213-1 hyster 30 ft 2005 what does it mean
DTC 524213-1 – Horn Alarm Output Driver OC
POSSIBLE CAUSE
A. HORN OUTPUT DRIVER SHORT TO BATTERY
B. HORN OUTPUT DRIVER SHORT TO GROUND
C. HORN OUTPUT DRIVER OPEN CIRCUIT / HORN +VE SUPPLY OPEN CIRCUIT
D. FUNCTIONAL FAILURE IN CONTROLLER
I have a yale erc070vg with a code of 12802 and cannot find any information on it, help appreciated thanks
Hello I Have a Hyster stand up forklift and im getting error code 40085 Steer key input voltage OOR. Does anyone have any info on this error code? Thank you
I have fault code 523860-4 truck disabled on my Yale 50vx. And hoping you could help me with what this problem is
DTC 523860-4 – Brake Pedal Position Sensor OORL
POSSIBLE CAUSE
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Error code 12800
Getting an error code 522810-4 and can’t find it on the code list. Any idea on what it would be?
Thank you
Can be the alternator excitation signal reading is low. Check the wiring to the alternator. Look for short-to-ground or open circuits.
The problem can also be in the PDM.
I have a E60XN-33 and its having issues going forward and reverse. The forklift does turn on, it just doesn’t move. It shows no fault codes.
Thank you in advance!
Buenos días tengo este código
524269-7 . Me habla de problema un una válvula. Pero de que válvula me esta hablando?
DTC 524269-7
Transmission Enable Valve Failure
Pressure In Transmission Clutch Pack Above Normal After Transmission Enable Valve Is Commanded OF.
POSSIBLE CAUSE:
VALVE FAILURE
Hello. Can you help me please to find code explanation for 12849?
Yale ERC22-35VG. Thanks
Yeah hyster-yale order picker, reach trucks and Tugger… How do you override or disable lidar?
Hi, We’re working on a Hyster S100Ft serial G004V01673D and we have a code 522740-6. Can anyone help?
DTC 522740-6 – Oxygen (O2) Sensor Heater Short To Ground (Bank 2)
POSSIBLE CAUSE
A. SENSOR HEATER DRIVER RETURN SHORTED TO GROUND
B. FUNCTIONAL FAILURE IN CONTROLLER
Bonjour, savez-vous ce qu’est un code d’erreur YALE AL79 ? Merci pour votre réponse bien a vous
Le code d’erreur AL79 sur un transpalette Yale peut indiquer une défaillance du système de levage du transpalette. Plus précisément, ce code d’erreur peut indiquer que le capteur de position du levier de levage est défectueux ou que le levier de levage lui-même ne fonctionne pas correctement.
Pour résoudre ce problème, vous pouvez commencer par vérifier visuellement le levier de levage et le capteur de position pour voir s’ils sont endommagés ou mal positionnés.
Vous pouvez également vérifier les connexions électriques pour vous assurer qu’elles sont bien serrées et qu’il n’y a pas de fils cassés ou endommagés.
Si le problème persiste, il est recommandé de contacter un technicien ou un concessionnaire agréé Yale pour effectuer une inspection plus approfondie du transpalette et diagnostiquer la cause exacte du code d’erreur AL79.
Ils pourront alors effectuer les réparations nécessaires pour remettre le transpalette en état de fonctionnement normal.
Bjr moi aussi j’ai ce code Ici
E696
H20
Année 2019
Il démarre mais naccelere pas
Hello
code 30103 traction can bus from lift.
What that means?
The error code 30103 on your forklift refers to a communication issue with the traction control system over the CAN bus network.
This error indicates that there is a problem with the communication between the electronic control modules responsible for controlling the lift truck’s traction and speed.
The CAN bus network is a system that allows various components of the forklift to communicate with each other.
If there is a break or interruption in the communication, the error code 30103 will be triggered, and the forklift may not function properly.
There are several possible causes for the error code 30103 on your forklift, so the solution will depend on the specific cause of the problem.
Here are a few possible steps you can take to troubleshoot and fix the issue:
1- Check the CAN bus wiring: The error code may be triggered if there is a break or interruption in the wiring of the CAN bus network. Check the wiring harness and connectors for any signs of damage or wear, and repair or replace them as needed.
2- Inspect the electronic control modules: The error may also be caused by a faulty electronic control module (ECM) responsible for controlling the traction and speed of the forklift. Inspect the ECMs for any signs of damage or malfunction, and replace them if necessary.
3- Update the software: In some cases, the error may be caused by outdated software on one of the electronic control modules. Updating the software can sometimes resolve the issue.
4- Consult a technician: If you’re not sure how to diagnose or fix the error, it’s best to consult a trained technician with experience in troubleshooting and repairing forklifts. They can use diagnostic tools to identify the cause of the issue and recommend a solution.
It’s important to address the error code 30103 promptly to ensure the safety and proper functioning of your forklift.
Hyster pallet jack with the code MainCont. FIT30068, what does this mean?
DTC 30068
MainCont (Stuck Open)
POSSIBLE CAUSE
A. MAIN CONTACTOR COIL WIRING FAULT
B. FAULTY B(+) CONNECTION
C. MAIN CONTACTOR STUCK OPEN
D. FAULTY TRACTION CONTROLLER
I have a code 522735-5 can anyone help me the truck is a S50FT
We explain before on November 9, 2021
Buenos día. En mi tablero Yale GLP050VX me sale. HYDRAULIC INTERLOCK SEAT SENSOR.
25104 Code E60xn
I have an error code 523859-4 what does it mean
Please take the time to review the comments I made on December 21, 2020
I have and error code E641 Hyster 50XT Forklift any idea what that is?
Hello,
Have a 201 Hyster Model H550HD with error code: 1110
Runs fine no issues, pls advise
Yale ERP035VTN36TE084
Error code 12935. Forklift runs fine but the lcd backlight doesn’t come on.
Any help would be appreciated.
What is code 1206
witch model?
Hello, we have Hyster 1.75 elec. And have a error code -143. Wath is de problem? Thank jou,greetings from Belgium
A code comes up but is not listed in your fault codes. Could you assist? E649
Propane Yale forklift. PSI engine.
my error is fault: 524238-3
DTC 524238-3 – Rear Wiper Motor Driver OORH
POSSIBLE CAUSE
A. WIPER ARM STUCK OUT OF PARK POSITION (OBSTRUCTED) (THERMAL SWITCH
OPEN) (DTC 524237 OR 524238 ONLY)
B. PARK SWITCH SHORTED (DTC 524237 OR 524238 ONLY)
C. MOTOR/PUMP DRIVER OUTPUT SHORTED TO BATTERY
D. MOTOR/PUMP DRIVER OUTPUT OPEN CIRCUIT
E. MOTOR/PUMP DRIVER RETURN OPEN CIRCUIT
F. MOTOR/PUMP/FUNCTIONAL FAILURE IN CONTROLLER
Yale NTA030SB I have a mod9/2 code anywhere I can find this info out at
Yale
Fault code 100-3
DTC 100-3 – Engine Oil Pressure OORH
POSSIBLE CAUSE
A. SENSOR GROUND OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT (OIL PRESSURE ONLY)
C. SENSOR SIGNAL SHORTED TO SENSOR SUPPLY
D. SENSOR SIGNAL SHORTED TO BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
i have a 524249-2 code on a 2008 Yale 155VX could someone give me the cause
Hyster 60xt with codes c001, c003, c005, c007 and c009.
Hello, I have a hyster 2.5 elevator, it does not give a start signal, co 13 and co 26, I would like to know what they are, how I could solve it, if I can reset it, the machine raised a fault in the battery, a jumper was made to start it, thank you very much in advance, greetings from Argentina
Hello I have. Yale 50xt with an error code co28 won’t start turns over but doesn’t fire just got this machine so I don’t know a lot about it. Please help!
Mike
hyster h5.0ft pannel going on but cant start and all the codes are running fast, please help,omhow to resset the modul on contro pannel
Error 696 replaced controller. Unit starts runs fine then code comes up and unit losses throttle
What does Err E649 mean? Yale forklift GTP050MXNEAE086 DIESEL
what mean code
523249-4
522766-3, 10284
523244-4 ,10025, 2023-12, 2236-12
DTC 523249-4 – Lever 4 Position OORL
POSSIBLE CAUSE
A. MINI LEVER FAILURE
B. MINI LEVER MODULE (MLM) FAILURE
C. FUNCTIONAL FAILURE IN CONTROLLER
DTC 522766-3 – Ignition 3 Relay (RL1) Driver Output OORH
POSSIBLE CAUSE
A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED
B. SHORT ON RELAY DRIVER OUTPUT TO UNSWITCHED BATTERY (SEE WARNING BEFORE CONTINUING)
C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY.
D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE
E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT
F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT
G. FUNCTIONAL FAILURE IN CONTROLLER
DTC 2023-12 – CANbus Error With Display
DTC 2236-12 – CANbus Comm Error With MLM
POSSIBLE CAUSE
A. TERMINATION RESISTOR(S) OPEN CIRCUIT
B. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO
C. CAN HI AND CAN LO SHORTED TOGETHER
D. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES
E. STG ON CAN HI
F. STS/STB ON CAN LO
G. CAN CONNECTED DEVICE FAILURE
I have the error picture on my yale erc050. Its a picture of the top being lifted. But it isnt. As if the seat is open for charging. But it isnt. It is intermittent. Where is the sensor located so i can check it up??
Hello. Can you help me please to find code explanation for 12849?
Yale ERC22-35VG. Thanks
Hello. Can you help me please to find code explanation for 12849?
Yale ERC22-35VG.
code 65513
Hello,
Hyster A1.5 error 21569. I tried to change the contactor and other electrical parts, such as relays and VFD, but I still have the same error. May you help me, please?
Thank you.
Hello,
Im getting error code for a Yale MPB045VG, FLT30061, Mtr Open. Can you help me? Thank you.
POSSIBLE CAUSE
A. TRACTION MOTOR CABLE FAULT
B. TRACTION MOTOR FAULT
C. FAULTY TRACTION CONTROLLER
COMPONENT OPERATIONAL CHECK
NOTE: Always check battery condition and state of charge before performing electrical troubleshooting. A faulty
or low charged battery will cause electrical features to not operate as designed and give incorrect readings while
performing electrical tests.
PROCEDURE OR ACTION:
1. Conduct a visual inspection of all connectors/wiring associated with the fault code.
Are any faults detected/observed?
YES: Repair/replace connector or wiring associated with faults found. Refer to the appropriate Electrical
System SRM .
NO: Proceed to Step 2.
2. Re-key the vehicle.
Is the code still present?
YES: Proceed to Cause A.
NO: Problem may be intermittent.
CAUSE A – TRACTION MOTOR CABLE FAULT
PROCEDURE OR ACTION:
1. Inspect controller phase cable terminals for proper torque and connections.
Are phase cables properly secured?
YES: Proceed to Step 2.
NO: Repair and properly torque cables.
2. Disconnect the traction motor cables from the traction controller and traction motor. Measure continuity of individual cables to isolate fault.
Is continuity present?
YES: Disconnect battery and proceed to Cause B.
NO: Repair or replace faulty phase cable.
CAUSE B – TRACTION MOTOR FAULT
PROCEDURE OR ACTION:
1. Measure continuity between the traction motor terminals U and V.
Is continuity present?
YES: Proceed to Step 2.
NO: Repair or replace faulty traction motor.
Diagnostic Trouble Codes ELECTRICAL SYSTEM
Check the Service Manual section in Hypass Online for possible updates and check pertinent Grams
9030-20-20
(Cont)
2. Measure continuity between the traction motor terminals U and W.
Is continuity present?
YES: Proceed to Step 3.
NO: Repair or replace faulty traction motor.
3. Measure continuity between the traction motor terminals W and V.
Is continuity present?
YES: Proceed to Cause C.
NO: Repair or replace faulty traction motor.
CAUSE C – FAULTY TRACTION CONTROLLER
PROCEDURE OR ACTION:
1. If no faults are found, replace controller. Make sure to indicate the DTC code(s) on the warranty claim to include an accurate problem description leading to controller replacement.
hI, I HAVE A CODE 40070 YO DONT HAVE IT IN THE LIST OF CODES, CAN YOU HELP ME WITH THIS?
Hello, I have code 33051. Can you tell me what the problem is?
Model of forklift?