How to clear forklift error codes?
In all new generation of forklift and also some old models of forklift sometimes when you are using the forklift will see some error code on the monitor(dashboard) of the forklift.
In different forklift, each Error code means different things.
On Yale and Hyster forklift the error code can be showed or can be in the system.
Yale and Hyster Forklift Fault Codes List
for going inside the system you need the password that the company using or can be changed by the dealer before they ship it to the customer.
When you go inside the system you are able to see the error code and you will see how many time this error code showed in your forklift and also when (In witch hours of using the forklift), from the error code list that the company gives for each forklift to the dealers and forklift technician you will understand what is the problem and you can solve the issue with any headache.
In some other trucks same as Raymond, Toyota, and Nissan you will see the error code directly in the forklift and you can solve the issue and use the forklift easy.
How to detect and figure out forklift error codes?
In all forklift when the technician connect with computer to forklift all the issue and error will show up and he can fix for you, your forklift
Sometimes you see the error code in your forklift but you see your forklift work well, But it can be a point and you have to solve it because it is same as alarm and if you don’t ask the forklift technician for this issue in future you will be stuck with the bigger problem and big charge to repair your forklift.
Our suggestion is when you do your daily checklist please look and see your forklift doesn’t have any error code.
If you find any error code, don’t use the forklift to solve the issue.
How you can figure out forklift error codes?
Please leave the error code below this article then We and other specialists will answer you as soon as possible.
Our technician at Forklift Plus can detect and figure out your forklift problems as soon as possible.
I have a hyster h70ft with an error code 190-7 what does it mean?
Hi
error code 190-7 is Engine speed Exceeded command
Hi,
I have 3 Ton Hyster, It’s not Moving Forward; Reverse after completing the Transmission Overhauling.
If i will give Direct supply to F / R Solenoids its moving.
Hi
The solenoid valve is plumbed to an existing lift truck hydraulic function. When the button is depressed the solenoid valve changes the direction of the hydraulic fluid from its original function to the additional function.
Hola tengo un hyster modelo S70FT solo retrocede y cuando acciono el pedal para que avance me da error 524271-2
DTC 524271-2 – TISS Sensor Pulse Count Low
POSSIBLE CAUSE
A. SENSOR SUPPLY/GROUND OPEN CIRCUIT
B. SENSOR SIGNAL(S) OPEN CIRCUIT
C. SENSOR SIGNAL(S) SHORT TO GROUND
D. SENSOR SIGNAL(S) SHORTED TO +5VDC OR BATTERY
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
N
Postovani imam kod greske na yale 522781-3
The code is here
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
DTC 522781-3 – MONOTROL® REV Switch OORH
POSSIBLE CAUSE
A. MONOTROL® SWITCH OPEN CIRCUIT
B. MONOTROL® SWITCH SIGNAL SHORTED TO SUPPLY VOLTAGE
C. MONOTROL® SWITCH SIGNAL SHORTED TO BATTERY SOURCE
D. MONOTROL® SWITCH FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
06 code.on yale
Hi I have jac battery counterbalanced forklift truck model CPD25 and problem with it can move front and back. Alarm 101 warning 89 n 91. Please if you can help me in rectify the fault.
Thanks,
Vinesh Gounder
524223-1
you can find it here https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
64974
33037
Hi I have a Yale cdp30mx 2017 and it won’t start it’s coming up with an error code Errd000 please if any has any advise that would be a big help,
Thanks wayne
Hello Wayne!
I have a Hyster H5.50xm 2001 and the display shows code 15. What does that code mean?
Thanks!!
Yale picker that willnt move but shows code 8996 13058 what does that mean
52 str encoder fault
I have a Yale NR035DBNS24TE095. I had Code 60055. I will not tilt when code comes up.
I have a hyster 60 fortis I have a code of 522660-0 can you tell me what the issue is the technician says it’s a fuel problem but it’s running fine, any answers for me
Thanks josh
DTC 522660-0 – Long Term Closed Loop Correction Bank 1 Less Than NOR -35% (Rich Engine Operation)
POSSIBLE CAUSE
A. PROBLEMS THAT MAY CAUSE LEAN ENGINE OPERATION
B. PROBLEMS THAT MAY CAUSE RICH ENGINE OPERATION
C. SENSOR FAILURE
D. FUNCTIONAL FAILURE IN CONTROLLER
Hyster Electric Lift Truck Model E50XN-33. Display shows picture of a key. No error code. No startup.
Hi error code 524250-14 (truck disabled)
Hi,
You can find it here : https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
HI I have Yale ERP20VFLWB E2380. Display is blinking with 9004 error code.I can’t find this code anywhere.
Have a hyster w40z will move but not lift just sounds horn code is E108
Saya mengalami masalah kode 38 pada forklift hangcha 2.5 ton.bagaimana cara mengatasinya
Yale 36k forklift gdp360ececcv144 throwing code ho928
I have an H70FT diesel. I removed engine to replace flywheel. Runs well and all functions work. But I have a code Its
100-4. Dashboard is showing hydraulic inter lock seat. Checked connection at seat sensor. Any thought
please check here https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
I have a Hyundai and the code is md6 I believe it’s saying side battery REM
Have a hyster fortis 120 with code 524269-3 last 9357,can you help
DTC 524269-3 – Transmission Enable Valve Coil Driver Output OORH
POSSIBLE CAUSE
A. RELAY/COIL DRIVER OUTPUT SHORTED TO BATTERY
B. RELAY/COIL DRIVER OUTPUT OPEN CIRCUIT
C. RELAY/COIL DRIVER RETURN OPEN CIRCUIT
D. FUNCTIONAL FAILURE IN CONTROLLER
Merhaba Hyster akülü forklift J40ZT 1.6 ton makinam 215R arızası var . Arızayı nasıl çözebilirim. Birde aynı makinamdan 1 tane daha onun arızası 222 veriyor
I have an electric lift truck model E65XM with error code 7 accelerator voltage too high
Hi I am getting the code 636-2
I think i saw it says that is a crank sensor. Is there a danger of running the machine with this fault?
Error 12456 yale eléctrico?? Que es
Toyota error code 0224
I have a lift truck model gtp25tk with an error d007 what does it mean?
Hyster error code 12833
My code on a yale fork lift is 12834. 25606 thank you
12576
DTC 12576 – Motor Voltage Not OK: If this is a new series truck the code indicates an open motor circuit. It could also be a failed motor controller.
DTC 12834 – Aux Driver Short to Bat (-) Brake Coil Open Circuit
Hallo,
Ich habe ein Gabelstapler hyster Modell E50XN-27.
Ich habe seit einigen Tagen ein Fehlercode 12832 auf dem Display.
Was bedeutet das??
Ich bitte Sie um Hilfe.
Ich bedanke mich herzlich.
Mit freundlichen Grüßen.
The code “12832” indicates that the controller has detected an open circuit or short circuit in the traction motor wiring
I have a newer Hyster throwing this code but drives fine any tips as to what causes this? Forklift is very clean
Code?
Kode kesalahan T0231
Fault 522631-2
DTC 522631-2 – Oxygen (O2) Sensor Fails To Switch To Rich Bank 1 (Lean Engine Operation)
POSSIBLE CAUSE
A. PROBLEMS CAUSING LEAN CODES
B. PROBLEMS CAUSING RICH CODES
C. SENSOR FAILURE
40062 steer motor encoder
Código 524223-4
Check this link:
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
i have 16ton hangcha error code M14..and emgine light do not off
2019 model mitsubishi forklift error code F 31
Sensor battery error
1. Wheel sensor bad 1. Wheel sensor check
2. VCM bad 2. VCM check
3. Harness bad 3. Harness connection check
Hyster B60zac
Error 32099
Any help what code means
Hyster 5.00 fork lift
524213 fault code
524269-3 fault code
Doesn’t want to start
You can find here https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
error code 12800
Brand and Model of the forklift?
I have a error code 30068 on my yale pallet jack, what does this mean?
DTC 30068: MainCont (Stuck Open)
POSSIBLE CAUSE
A. MAIN CONTACTOR COIL WIRING FAULT
B. FAULTY B(+) CONNECTION
C. MAIN CONTACTOR STUCK OPEN
D. FAULTY TRACTION CONTROLLER
I have a Yale that has two fualt codes (522772-4) and (880-4) and I can not find anything on em any help would be awesome
522772-4 Backup Lamp Driver Output OORL (out of range,low)
880-4 – Stop Lamp Driver Output OORL
A. LAMP DRIVER OUTPUT SHORTED TO GROUND
B. FUNCTIONAL FAILURE IN CONTROLLER
Hibi jave a hyster 3.oft with 177 error code
for Possible Cases please check the below link:
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
Code 64974
Yale ERP040vtn36te082
I have a raymond swing reach giving me code D2
What is fault 39 on electric lift. Truck Yale MP20?
Hi Yale electric forklift will not go up or down goes forward and back I’m getting an error code 22531
Hi
Hyster forklift H5.0ft is show f627-2 what does it mean and what can I do to help me out
627-2: Power Lost without Ignition Off – Data Erratic, Intermittent, or Incorrect
Buen dia me aparece el codigo de error 524223-4 y no entra ningun cambio.
DTC 524223-4 – Transmission Reverse Pressure OORL
POSSIBLE CAUSE
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
ERROR CODE 087 IN TCM 200 ELECTRONIC FORKLIFT
I have hyster forklift start 30sc stop Eng l ve coude 2350_3 and front light not working
DTC 2350-3 – Front Work Lights Relay (RL4) Driver Output OORH
POSSIBLE CAUSE
A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED
B. SHORT ON RELAY DRIVER OUTPUT TO UNSWITCHED BATTERY (SEE WARNING BEFORE CONTINUING)
C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY.
D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE
E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT
F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT
G. FUNCTIONAL FAILURE IN CONTROLLER
Hyster H120FT, fault code 627-2. I can’t find it any where in the manuals or online.
627-2: Power Lost without Ignition Off – Data Erratic, Intermittent, or Incorrect
Ik heb een hyundai hbf 18t-5 en geeft als foutcode BDI CUT OUT
Grtz chris
Hyster 120 H120FT
Error code 524213-1
DTC 524213-1 – Horn Alarm Output Driver OC
POSSIBLE CAUSE
A. HORN OUTPUT DRIVER SHORT TO BATTERY
B. HORN OUTPUT DRIVER SHORT TO GROUND
C. HORN OUTPUT DRIVER OPEN CIRCUIT / HORN +VE SUPPLY OPEN CIRCUIT
D. FUNCTIONAL FAILURE IN CONTROLLER
Toyota error 142
Hello. I have a yale 0s030 order picker
It gave me an HeightError code , and stop moving and lifting.
I assmned was hydraulic oil low,
How do i errase the error code, or if keeps showing up.. what are the ootions of dealing with this erro. Ive checked the pumpmotor and it is working. Not 100% sure if pump is working , i do not think it will fail suddenly..
Any ideas ??
Hello! I can’t find information on errors – h0316, h0216, h 0116. Forklift YALE GDP 180 EC. Thanks!
Hyster 60 XT com erro d000
Hi Error 60 on node 3, in an electric forklift.
How to solve that?
Hi we have a maximax electric Forlift and warring node 2 mean? Then we had another one and few months ago say warning 62 node 2.
hi i have a 6024 error code on a hyster j3.0xn. What can be?
thanks in advance
I have a yale forklift, propane ran, code 524264-2 no trans brake, were do I start, I’m new to working on these machines
DTC 524250-14 – TOSS/TISS Special Conditions,
toss sensor 1 no output DTC 524265-2 – toss sensor 2 no output DTC 524271-2 – tiss sensor pulse count low DTC 524225-14 – toss sensor dual output failure possible cause a. sensor supply/ground open circuit b. sensor signal(s) open circuit c. sensor signal(s) short to ground d. sensor signal(s) shorted to 5vdc or battery e. sensor failure f. functional failure in the controller
I have a Yale forklift with a fault code showing up as 52424-4. What does thid mean?
I think you miss a one-digit number in code(52424?-4) please check again and let us know
We have a yale lift error code is 33034. It’s not moving anything at all. Battery is charged and i can go through the control. But it showing
103 code TCM
Drive safety circuit turns on
I have a Heister 35 XM the coach to come up or 251and68Where is it trying to send me.
I have a Toyota forklift the model is 8bru18 and electric 36 Volt
the code coming on the dash is 37.
Can you help me whatis wrong with it please.
Hi
Code 37 is for Lift potentiometer.
You have to get inside of the program and reinstall it again and if you have the same code it is better to change it.
Hyster electric forklift
Error code 150
krisbow electric error code alrm 103
I have fault code 884_4 can you help
Brand and model ??
Hi! Hyundai model 30B-9F error P4F ..what that is mean
Hi
I have a Toyota Forklift model 8FGCU30 and I have a error code C5-4 and I cann’t use the accelerator and don’t have a power in engine . Do you ave any idea about it.
Hi
This error code warning you about the connection between the accelerator pedal and distributor
Check the harness between pedal to go through the engine and also check the connector in the right step and the connector in left step to computer
Model N30ZDRS2 alarm code 9001
Hi
We have a Raymond forklift Model 4450 . the forklift is working but it is the error code C4 in the monitor .
Do you know what is this error code and is it dangers or is it any way to remove this error code?
Thanks advance for your help.
For the error code C4 have to check the wiring system or bulb for backlight
it can be short on this wire or the backlight have to be a change.
I have a hyster code E0285
Hi I have problems
523930-4
Hi,
check this link https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
Hi
I have a forklift Raymond Model is 4450 and the error code 1c is show me in the dash I unpluged and pluged the battery but samething I have and when I want to go reverse the speed will be too slow or will stop the forklift.
Do anyone have the idea what is wrong with it? and what is the solution.
I am so far from the big city and it is not easy for me to ask dealer to solve this issue because they will ask 4 to 5 heurs distination charge.
Thanks advance for your help.
I hope it will be helpful to fix your forklift and don’t need to pay a lot to find the Issue and use your forklift again
At the first point check the voltage in your battery or you can ask someone to test your battery
Most of the time it is low voltage in the battery
please check it and if it is not soled let us know
regards
Hey I have a code of 1382 coming up on my Hyster model E55-XM33
Hey I have a code of 1382 coming up on my Hyster model E55-XM33, wondering if anyone could help.
Thanks
Hi. We have a hyster j40xnt with error code 33029. Just wondering if you can help with this.
hyster H3.0TX S/n B466R12891L Washrd machine now code errd000 appearing data receiving time out error
what to do
It is the problem with sort of amper failure inside the soudtouch. The simple way is disconnect the battry for 30 second and connect it again.
Power jack stopped dead saw error code c 66 no one seems to know of this one. Now i’m seeing a code c-30. We are 3 hrs from Thunder Bay shipping is pricey, so would like to figure this out without sending it out. Had batteries tested they all show 6.1 volts, its a 4 battery 24volt system. We tested charger it seems to be not showing anything. they charge percentage says 86 its been on that for last three days. Any help would be appreciated , Thanks.
The code C-30 is for belly bottom switch, please check it maybe it is not in right place or broken.
I have a Hyster Fortis 40 with the fault code 190-8 showing on the console. Can you tell me what this code is for?
Hi, your forklift problem comes from Crank/CAM Synchronization, please check!
Salve ho un Hyster 3.0 Fortens mi segniala il codice 190-2 sapete che cos’è
DTC 190-2 – Engine RPM Sensor Output Is Less Than Engine Speed
POSSIBLE CAUSE
A. OPEN CIRCUIT IN SENSOR SUPPLY
B. SENSOR SIGNAL OPEN CIRCUIT OR SHORT TO GROUND
C. SENSOR SIGNAL SHORTED TO BATTERY SOURCE
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Yale ERP040VTN36TQ090 error code 21569
Hi there, We have a Toyota 8hbw23- error code showing up is 152. machine will not turn on or re-boot
Hello,i have forklift stiil rx60/50
In display have code A1401. forklift not forward,backward so material handling not working.what problem and solution.tank you
Hi, We have a Yale GDP160EC & it has just started coming up with error code h0928, can you please advise if this isa hydraulic oil?? oil level is good & no leaks.
Hi,
Verify the harness and battery condition.
maybe the battery has to be change.
enjoy
I have aHyster s155 fortis seem,s to be working ok .But fault 522800-13 has apeared on display what does this code mean
Hi,
You have to check and calibration Valve
Hi, I have a Hyster forklift H3. 0FT fortens and it’s giving error code 51-7 and can not accelerate. How do I clear the fault code
DTC 51-7 – Throttle Position Sensor Signals A and B Not At Commanded Value
POSSIBLE CAUSE
A. ELECTRONIC THROTTLE BODY STICKY
B. THROTTLE MECHANISM INCORRECTLY ADJUSTED
C. SENSOR (THROTTLE BODY) FAILURE
D. SENSOR SIGNAL CIRCUIT HIGH RESISTANCE (MAZDA ONLY)
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
Correction ERROR CODE 078 . . . ?????
Hi,
Please let me know the brand and model of forklift
I have a yale with an fault code of 524223-0 what is this and how do I reset it?
Hi,
XMSN Reverse pressure greater than commanded pressure
can be from 3 reason
1. sensor supply open circuit
2. functional failure? (mechanical)
3. sensor failure
each reason need to check and change something
HYSTER H50FT: ERROR CODE 523746 not sure what this means
Hi
it means key switch/start switch failure ;)
Hyster 5.50xl elettrico sul display compare -16
Check the Voltage of your battery and the ampers on it.
If you can try with another battery will be great if the issue not from the battery have to check the EV100 or set it with handset
Hi
I have a Hyster 3.0 Fortens
Error code 524269-3 Any idea what the issue is?
Hi,
There are four possible causes that cause this failure,…
– possible failure–
1) relay or coil enable in short circuit with the battery
2) relay or coil enable with open circuit
3) relay or coil enable, return to open circuit
4) functional failure in the controller
forklift hyster J3.5GX error code: C01, C03, C06, and C09
Merhaba Yale GDP 35 markalı forkliftim var 522772-3 diye arıza var
Yardım lütfen
DTC 522772-3 – Backup Lamp Driver Output OORH
POSSIBLE CAUSE
A. LAMP DRIVER OUTPUT SHORTED TO BATTERY
B. INTERMITTENT SHORT OR OTHER POWER SOURCES
C. FUNCTIONAL FAILURE IN CONTROLLER
Hi,I have a Toyota BT Reflex RR200E that appears 4:266 error code on painel/dashboard.. help please
Hi, we got error code 59 on a Raymond EASI DR30TT any information would be appreciated, thanks
Hi,
Code Title: Software error – Can’t Transmit
How to clear: Cycle the key switch On/Off
Replace the Vehicle Manager, before replacing the vehicle manager, use the operator display to verify that the firmware is working properly.
Regards
Forklift Plus
Hi I have a Crown electric forklift and I am getting Error 309. Any idea?
Hi,
Right-Front Wheel Sensor Circuit Failure
Hi am Isaac ihave 7tonne hyster forklift has afault code of 523930-3
Hi,
Your answer is in this link https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
anyway : FWD Circuit Shorted High and Possible Cases is :
A. COIL DRIVER OUTPUT SHORTED TO SYSTEM VOLTAGE
B. COIL SHORT CIRCUIT
C. FUNCTIONAL FAILURE IN CONTROLLER
Toyota Electric Forklift Truck Model 6BRU23. Error Code 65
Hi,
This code comes from the deadman pedal, failure detected, please check the switch and wiring for the deadman pedal
Hyster model E30HSD2-18 Error code 50068 pump main contactor not closed
Check the hydraulic pump brush
Hello – Yale ERP030 codes 207, 209, 209L, 226
We have a Hyster forklift and while driving along the forklift will cut off and show a code 8976 and this is a safety issue because the forklift has to coast to a stop because the brakes inop when it cuts off.
Yale error code 208 and 204 what is it and how do you reset it?
check the switch and wiring the hood for code 204 the hood has a switch on it to disable operation if it is not closed,
and code 208 check the battery:
make sure the battery is filled and fully charged and has no problems in any of the cells
Hi
There are 2 error messages on display(2 and 260 these errors appears when i wanna use the forks up/down. the errors disappears if i turn off the switch for 5 min,and will be back if i use hydraulic system again.
Its YALE ERP040THN48TE082
Thank you so much
SJ
Hi,
error codes 260 for low voltage to pump motor :
you have checked both of the pump motor cables and checked the pump motor for continuity, I would start with checking pump cables for short to frame. Does the truck drive? If not check for the voltage drop across the main contactor. If all checks OK. You probably need to replace the controller
:)
Regards
Hi, I have Yale forklift and after I start up run very well but after few seconds sometimes minutes I can’t accelerate and after few seconds stop. Unfortunately I can’t access to error. I check the fuel system, battery and Are ok.. Thanks
Hello forklift plus crew.
Nice site you have here.
I have Yale forklift
model ERP 16 AAF E2130
year 1998.
Error code -16 is displayed. Can you help me and is there anything i can do to fix this. Ty for your reply.. 😁
forward and backward function is not working fault alarm is 524223-1
XMSN reverse pressure less than commanded
I have a Yale model GLC155VXNEUV107 has fault code 522800-13 can you help please
It’s transmission valve calibration
I have a Toyota reach truck, model 8BDRU15
Error code 67 what does it mean?
error code 67 relates to the lift height switch on the mast, generally they do not give much bother, have to check the wiring to the sensor it may be damaged.
I have a Yale ERC 060 RG with a fault code 05
Error code 05: Start switch fails to close.
Symptom: Forklift does not move.
Possible Causes and Test Procedures:
Malfunction of the start switch circuit. Check for open circuit or loose connections in wiring from the key switch to start switch and from P16 to start switch.
Malfunction of the start switch. Check the start switch for correct operation and output.
I have a Toyota reach truck, model 8BDRU15
Error code 61
what does it mean?
The code 61 is a steering error, outside of the steel brushes being bad the relay on the steering controller may not be closing causing the problem. maybe the relay is bad or wiring to the steering controller.
Anyone come across error code 4C for a Raymond model R35-C35QM
Raymond Tech still isn’t out here on day 2 with no lift, wondering what the code might mean.
The 4C that is the steer contactor, check the steering fuse, Check the contactor, check the Fuse, Steering Motore and Harness for the power steering motor
524225-1 hyster H100Ft lift disabled?
Code 524225-1 is low pressure forward
1. Check Transmission oil level.
2. No power to sensors Is voltage approximately 5V dc on wire 256?
3. FWD 1 Sensor has failed,
4. Clutch or pump failure , check pressure of 896 to 1000 k Pa (130 to 145 psi)
Hyster 60xt error code C028
I have a Yale GLC050LX with error codes 523769-2 and 523767-2 but cannot find any info on them.
DTC 523767-2 – DSC Fault – Arrow Down Button Stuck
DTC 523769-2 – DSC Fault – Arrow Up Button Stuck
POSSIBLE CAUSE:
A. BUTTON FAILURE
PROCEDURE OR ACTION:
1. Disconnect battery + connection.
2. Replace display. See Electrical System 2200YRM1427 or Electrical System 2200YRM1327 .
3. Restore battery connection.
4. Turn truck power ON and press both the Scroll arrow buttons for two seconds.
Are any fault codes (DTCs) displayed?
YES: Go to the troubleshooting procedure as indicated by the DTC(s) and follow the troubleshooting procedures.
NO: Problem has been corrected. Resume operation.
Hi I have a hyster 2.00 electric forklift when I turn the key on it says 16 and then when I turn it of it says 01311. The battery is fully charged but the forklift will not move at all!
Hi
# “16” can indicate too high voltage in the battery, and would (correctly) happen if the controller was adjusted for a 36volt battery, and you installed a 48-volt battery,
The correct fix would be to get your battery checked and fixed by a battery company and to have someone with an ev100 handset to adjust function setting #15 to the actual ‘at rest’ voltage of the battery.
As an emergency workaround, turn on the lights and let them sit with the lights on for a couple of hours, then unplug and re-plug in the battery and turn the key on. this should drain some of the “surface charge” of the battery, and allow the controller to see a more accurate battery voltage.
You may be able to just do one or the other of the suggested “correct repairs” and have it work, but it would be far better (for many reasons, we can discuss if you want) to do both repairs; battery and adjust function 15 on the controller.
hyster 120 fault code…. 524237-4
Codes
DTC 524237-3 – front wiper motor driver OORH
DTC 524238-3 – rear wiper motor driver OORH
DTC 524240-3 – washer pump driver OORH
possible cause
1. wiper arm stuck out of park position (obstructed) (DTC 524237 or 524238 only)
2. park switch shorted (DTC 524237 or 524238 only)
3. motor/pump driver output shorted to battery
4. motor/pump driver output open circuit
5. motor/pump driver return open circuit
6. motor/pump/functional failure in controller
GOOD DAY
I HAVE A NISSAN FORKLIFT
MODEL: F1F1A180
2W300
SCREEN SHOWS ERROR CODE F-16
FORWARD AND REVERSE SWITCH WORKS, REVERSE ALARM SOUNDS, BUT THE FORKLIFT DOESNT MOVE.
HOW CAN I FIX IT AND CLEAR THE ERROR CODE?
Hi,
you can be going to check ‘pin to pin’ from the directional switch to the ECM.
Did someone install the backup alarm?
I have a 2018 Yale GTP050MX with a E602 code present. Cannot find code listing anywhere, any help would be appreciated.
Hi, I have a forklift model 8BWS13.
Lift function doesn’t work.
It travels and no shows any error code.
I’ve checked the hall effect potentiometer and it shows 2,5v up to 5v or down to 0.
what can I do to fix this situation?
Hi,
The first point you have to check with good battery with a full charge the next point please check the limited switch
Best
I Have a propane Yale GLP100MJ showing an error code 115 it runs for about 30 seconds then shuts itself down and engine light comes on, any idea what this code is
Thank you
I have a Toyota stand up electric order picker with an error code 43? any suggestions?
The voltage detected at JPC8-10 is less than 22V when the pump contactor (LPC) was commanded open.
1. Check for binding in the contactor. Repair or replace as necessary.
2. Using an ohmmeter, check the resistance of the coil. With the wires removed from the X and Y terminals, the resistance should be 10-50 ohms. Replace as necessary.
3. The cable JPC8 from the Interface Card to the contactor coil may be bad. Check it for continuity. Repair or replace cable as necessary.
4. Using a voltmeter, check for B+KC (36V) at JPC8-14 (+) with reference to TP4 (B-). If B+KC exists at JPC8-13 but not at JPC8-14, replace the Interface Card.
5. Measure the voltage at TP1 (contactor fuse panel) with reference to TP4 (B-). It should read B (36V). If it does not, then check the K3 relay. Replace as necessary.
6. If B+KC is present at JPC8-14 (+) with reference to JPC8-12 (B-F) and the contactor still will not operate, replace the Interface Card.
I have a hyster 3.0 fortens with error code 676-3 starts soon times
error code 59 toyota order picker
hello can someone help me I have a forlift toyota 8fgu32 and I have the code E 06-2
Hello, I Have a Hyster J1.60XMT and the error code is 250L Rotor Left Locked. Can you help me?
Raymond forklift Model #DSS 300TT it has a error code 44
I have a Hyster fortens 2.5 with Error code 523859-4?
523859-4: Service Brake Pressure OORL
A. SHORTED RELAY COIL
B. SHORT TO GROUND ON PDM RELAY DRIVER OUTPUT
C. FUNCTIONAL FAILURE IN CONTROLLER
Hi fotens 2.5 fault code 524230-3
Serieal no. L177B17770E
Hi,
PLEASE FOLLOW :
524230-3 Rear Work Lights Relay (RL7) Driver Output OORH
A. SAFETY SWITCH (IF EQUIPPED) IS DISCONNECTED
B. SHORT ON RELAY DRIVER OUTPUT TO UN SWITCHED BATTERY (SEE WARNING BEFORE CONTINUING)
C. SHORT ON RELAY DRIVER OUTPUT TO SWITCHED BATTERY. D. SHORT ON RELAY DRIVER OUTPUT TO ANOTHER OPERATED DEVICE
E. CONTROLLER DRIVER OUTPUT TO RELAY COIL OPEN CIRCUIT F. RELAY COIL OR GROUND CONNECTION OPEN CIRCUIT
G. FUNCTIONAL FAILURE IN CONTROLLER
hi,
i have forklift CROWN 40 fctt-188. the error code 152 on the dash. please help.
I have a Hyster B60ZAC Ride on Pallet Jack and when I hit Jackrabbit it shut down with a Service code CO 12835 and stuck in the street. Will not power anything? Can’t find anything on this code?
Hi I’ve got a 2011 Hyster Fortis 120 with a fault coffee of 522631-2. I’m not able to find info on it would you be able to help?
Hi,
522631-2: Pre-Cat Bank 1 Sensor Fails To Switch To Rich
Hello!
I have a problem with my Yale.
The error code is 522762-4 Truck disabled.
I tried to chabge the filters for the gas and it didnt start after that just cranking. After a few hours times trying the error started to come.
Thanks in advance.
Hi,
522762-4: Switched Battery Voltage 3 (IGN 3) OORL
POSSIBLE CAUSE
A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY
B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND
C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND
D. FUNCTIONAL FAILURE IN CONTROLLER
NOTE
Please refer to the end of this procedure for supporting diagrams
Hello. I cant find anyone that has been able to help me. I have a clark ecg25 reading error code -03 can you help me with this
Hi got problem with stocklin error E39??
i have a code 40062 about steer motor. lift stoped in middle of isle….
Dobrý den vozík mi chlasí chybovy kod 624 265-2 a mam omezenou rychlost. A zavada cca po 1 hod jizdy zmizí. dekuji
I have a hyster H175FT, it is showing 522800-13 error. Anybody can advise me how to resolve this issue.
522800-13 – Transmission Valve Calibration. : The transmission has to be calibrated. You have to go int thru the display. Have the transmission at operating temperature. Go to calibrations, transmission, and follow the prompts that come up. It should take about 5 minutes if the trans is hot enough.
errco28 on yale 50
HI
i have FORKLIFT YALE ERP 20 VF and I have code 12332 and I don’t know what is that???
I try to get into display but no sucess forgot pass… Have the system some muster passs and what is fault code what I receiving.
The forklift I can drive but not lift ????
PLS HELP
did you find the solution to this problem we`re expiercing the same issue
3701-0 is the error code on the yale fork
DTC 3701-0: Excessive Particulate Matter 5
i have a yale 3.8l kubota diesel wont go forward or reverse code 524250-14 popping up whats this code please
DTC 524250-14 – TOSS/TISS Special Conditions,
possible cause a. sensor supply/ground open circuit b. sensor signal(s) open circuit c. sensor signal(s) short to ground d. sensor signal(s) shorted to 5vdc or battery e. sensor failure f. functional failure in the controller
I Have a Hyster J40ZT electric forklift error code “51 precharge” shows on dash. what does this mean and can I clear code. Forklift does not move
I’m not sure but: Check the PTC that connects across the large terminals on the line contactor. If it is missing or not connected the capacitor in the controller will not stay charged. This will cause a code 51. Also make sure nothing is connected to the supply side of the line contactor like a scanner or radio. This will also cause a code 51
How do you clear a code on a sit down flortlift LifTec code E32
error code 523253-12 having a problem with the lift cylinder. the tilt and side shift work on this as it should
523253-12: Lever 3 Position Data Invalid, Mini-Lever for lifting is maybe out of service
Hi, I have a Toyota 8BWS13. Showing code E250. Sometimes it’ll reset after plugging it in for a charge, but code still shows shortly. What could it be? Thank you
Hi,
E250 is the charger in sleep mode. Plug it in for a few minutes to wake it up. If that doesn’t work, check the display for a version from the charger. It may be a communication problem from the charger.
I plugged it in overnight to “reset” the machine. It was fully charged and shows 81% on the display. No ideas why. Could the charger be malfunctioning? It works now, but I think it the error code will show again.
Hi Good morning
I have a hyster forklift H3.0TX, serial # A380B05433T,
there is an error d000, the forklift starts but cant go forward, reverse and there is no hydraulic functions too.
can u help out please
my yale mpw065sen12t2748 pallet jack keep stopping after about 15 seconds. After reboot, it will lift and move then suddenly stop again. The error code it shows is 33. What could it be and how can I correct it?
Yale ERC040ZGN48TE084. No mast functions and codes are 144 (Transistors did not shut off) and 141 ( Pump control temp too high).
Can jump to the ground that goes to lift motor and motor runs. Is it time for a control box for the lift motor?
toyota electric, what would error code CB-3 mean, lift wont move or hyd wont work
I have a hyster 3.0 fortens with error code 676-3 starts soon times
I have a Yale veracitor 50 vx with error code 524w38-3 and can’t find anything about this code. Forklift is working good big don’t want to push it. Please help asap!!
I have a Hyster (sit-down) Forklift E60XN-33 throwing error code 12832. Everything operates properly from my observations. It was reported as having a steering and braking issue. I drove it for an hour without consequence. Any ideas?
I have a e71-1 error code on my toyota forklift what dose it mean
found a broken wire in the harness
Hi, I have a BT (Toyota) Staxio W Series, with error code 2.001 after pushing in the emergency stop button. Can pull out the emergency stop button, but still getting the error code and the Walkie Stacker won’t start, please help?
Yale 2.5t Electric error code 05 accl switch
wont move forward or backward
Malfunction of the start switch circuit. Check for open circuit or loose connections in wiring from the key switch to start switch and from P16 to start switch.
Malfunction of the start switch. Check the start switch for correct operation and output.
I have a 220 error code on my TCM forklift what dose it mean
Yale Electric Reach Forlklift: 52 STR Encoder Fault. please help & thank you!
GOOD DAY
I HAVE A NISSAN FORKLIFT
MODEL: UO1L18U
SERIAL NO. R1G-19984
SCREEN SHOWS ERROR CODE G-03,G04
Code E-03 is for the ECM power supply circuit, with no power to ECM for a predetermined time.
E03 VCM communication error
E04 ECM communication error
Hi, we have a s60FT with error code 522616-8? any suggestions? Thank you
Hi,
Please check this link : https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
hyster S7.0FT fault code 520416 – 13. any help as not on any lists. thanks.
I have a YALE stacker, forks won’t lift. It just beeps when you press on up & down. When you turn stacker on, it displays EP213, shows a wrench looking icon & then screen shows 107…any idea whats going on?
Thanks, Christian
The EP107 is not alarmed code, this is most likely the Model and software versions that flash on display when first turning on the machine.
Alarm codes are ALxx codes generally for zapi control systems.
If it is not displaying any codes on the display gain access to the controller and look at it, there should be a light flashing on it, see if it is flashing in any pattern. The pattern will probably be in intervals showing the 2 digit code, flash x number of times, pause for a sec and then flash the 2nd digit, then pause for 3 or 4 secs or so and repeat.
I am having the same issue with my Yale Stacker forklift. Continues to beep in motion forward and backwards. When I first received it, it only beeped in reverse. Code 213 comes up when it is first turned on
Any help, would appreciated
hyster H60XT error code E696. I have a manual and cant find this code. somewhere i read about something being unpluged? help anyone?
Good Day.
My Hyster Fortens 2.5 is showing 96-4 fault and occasionally 100 .
Please can you help me with the repair.
Hi,
Please check here: https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
Hyster H360HD2 S/N KO19EO1535P hr. 85 went into limp mode this is its
Codes : EO285 , E4572 , E3868 , E3714 , E4863 , E3712 .
we have a cat p9000 fork lift. we have error fault e30 that only occurs once in a while by turning the master key off it will go of for about week of useage then reappears have any ideas
DTC E30 is an ECCS C/U Error signal
No supplied power to the ECM for some predetermined amount of time.
ECM detects insufficient power supply.
ECM pin 119-wire 189-wire color Key off/ Key on! Running 0/ Battery volts
ECM pin ‘120 Key off! Key on/ Running 0/ Battery volts
ECM Pin 121-wire 190– wire color White. Must have battery volts all times
Check ECM grounds. Always 0,0 volts.
Hyster j40xnt worked fine up until my husband went to turn it on today. He painted it yesterday put everything back together and now it’s throwing the code 21569 and flashing the wrench as well as clicking and won’t start at all. He’s checked all connections and all seem to be fine. He’s on site working on it so looking for a response ASAP
The fault is line contactor open
Hello my j2.0xn LWB
Erroe 33029
This code indicates a loss of communication between the system manager and the pump controller through the Canbus. check your connectors at the VSM and the hydraulic controller.
G’day,
We have a Yale GDP30TK with an error code CO60 coming up, any suggestions on where to look and how to clear fault would be awesome
Cheers Ash
Hello,
We have Hyster reach truck show error 250-33 with slow speed, can you help us to resolve this problem
Thank you
Zakaria
Hangcha Electric Pallet Jack CBD20-TC1 model. Getting error codes 51 and 52. Cant find any info pertaining to these codes and hope you can help thanks
Steve
Pacific Swift Transport
I’m getting a error code AL 01 on a yale power pallet jack
AL01, 1 flash.
Condition- Connection/communication error between control card and traction motor.
Truck response- traction and hoist functions disabled.
Possible cause and test procedures
1) Loose or damaged elec. the connection between control card and controller. Verify connection at controller, verify wire harness connection at the base of steer handle, verify connection at control card.
2) Damaged or defective control card.
Measure voltage at pin 5, connector C on the controller. W/ control card disconnected, this should be about 12V; w/ the card connected, it should be about 3 – 9V. A reading of 0V or 12V w/ the card connected means that the card or connector pins are damaged.
AL01, 1 flash.
Condition- Connection/communication error between control card and traction motor.
Truck response- traction and hoist functions disabled.
Possible cause and test procedures
1) Loose or damaged elec. the connection between the control card and controller. Verify connection at controller, verify wire harness connection at the base of steer handle, verify connection at control card.
2) Damaged or defective control card.
Measure voltage at pin 5, connector C on the controller. W/ control card disconnected, this should be about 12V; w/ the card connected, it should be about 3 – 9V. A reading of 0V or 12V w/ the card connected means that the card or connector pins are damaged.
I Have a hyster 50xt, serial number A380V03530R, it has error code E641 on the display. Lift seems sluggish when moving, however I cant seem to find this code anywhere. I would appreciate any help.
Yale code 13380
have a yale. GLP090VXNKAF098 code 5273, i replaced the LP fuel filter. still has code. lift runs good ,has power and no performace problems, do i need to delete code or what is it
HYSTER 522762-4 WONT START OR CRANK
522762-4: Switched Battery Voltage 3 (IGN 3) OORL and for Possible Cases please check the below link:
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
TCM FRHB14-8A
Error code – 106
No function of lift. What we cand do?
Hello
I got some errors codes for a HYSTER 16-12
E2634
E1898
E2449
Any help will be greatly appreciated as there is an audio alarm for this codes and it’s a pain to operate the machine with the alarm on for long periods of time.
Thanks
Hyundia 25BC-9
When trying to use lever on steer column unit displays error code 3FT.
ciao
ho un errore su un hister H3.5FT serie L177B1290E ERRORE 524271-2 FRENO TRASMISSIONE DISATTIVATO, potete aiutarmi?
Sensore TISS. Registrazione di un impulso basso basso, scollegare il sensore e con il voltmetro selezionato controllare la tensione e il cavo del sensore – terra, dovrebbero esserci circa 5 volt se non si trova una messa a terra adeguata del telaio e controllare di nuovo l’alimentazione del sensore se si ha tensione ora controllare il filo di terra del sensore per circuito aperto. In assenza di tensione, collegare nuovamente il VSM per il circuito aperto e la riparazione. Se hai 5 volt tra e – sui cavi del sensore, cambia il sensore ed elimina il codice dal registro degli errori
I have an older yale elecric 3 wheel forklift had error code for right motor encoder,,,,we replaced it……..code is still there and forklift still disabled….do i need to clear the code or should it have fixed itself…if so it obviously wasnt the right fix we did
I was think of buy this Hyster S50FT Fortis 5000lb Forklift. The owner says, Now it throws a code on the dash that says truck disabled and won’t allow it to start? What you think
Richard
i have a hyster J1.75 ex fork , it goes into limp mode at random then back to normal, can do it a couple of times per day, no load on machine just normal driving
no error codes come up
battery lowest voltage 47.5
if it was batteries it would do it all the time
what do you think
cheers
graeme
Hi, I have a Yale GDP280 DP with error codes 30, 35 ,39 could you please tell me what they denote .
Many Thanks
Mike Maud
Hi, I have hyster forklift which model is h16xm-6, with zf transmission. The error message is t1110. This error turns on when engine is working. I need help
hey, i have a STILL FORKLIFT R70-20 and it provides the following error codes:
error 2 , error 194
hi, i need to erase the maintenance alarma for a a forklift toyota 40 7FG25. Help me please..
I have a Hyster model E60Z-33 with an error code 52. Can someone tell me what the problem is please?
Hyster E60XN 33 Error 12802
code is 12810 for the accelerator pedal connection
maybe you forget to plug the foot pedal back in after maintenance
I have an error code 52 on a hyster E60Z-33. Can someone tell me what this is?
Toyota 8HBW23
ERROR CODE;
E150
E152
E691
THANKS!!
E150: This can be a communication issue. check the handle switches and the wire going up the handle for breaks.
Hi,
I have a Hyster HE. 0FT and we recently replaced the VSM from a similar model but it displays VSM mismatch. What’s the solution on how to reprogram it?
Good day
i have hyster E40XN eletric rider that the dashboard refuse to come up after ignition is switch on.
i have check the fuses and the ignition relay,nothing is working.
please help me out.
I replaced the transmission on the Hyster H360 HD2 forklift. It kept giving error code t1506. Hyster’s software has already been passed but it hasn’t erased the flaw. I want to know how I can fix this error. I’ve switched connectors and nothing resolved. I’m waiting. Thanks
Hello,
I have Yale MR16N D840 forklift and it’s stop to work with code 062-05. Could you please tell me what the problem is please?
I have a Yale ERP030TH and it shows codes 10 and 224. Please tell me what the issues are? Thanks.
I have a Yale MTR005LFN24T that is spitting out error code “32052 Combi Sensor Fault” It only throws this code when it is put in reverse quickly and not if it is eased backward.
Hi! like your post, it’s very informative.
Need your help with my 3 wheeler electric Hyster forklift (indoor operations). I opened the battery compartment while doing maintenance but I can’t close it back what could be the problem?
Hi guys l hate a hyster H 50CT. A274V02282K
Error code 523740-4 could you tell me what it is
DTC 523740-4 – Truck has NO Forward or Reverse Motion
POSSIBLE CAUSE
A. HIGH EXTERNAL MAGNETIC FIELDS
B. DIRECTIONAL LEVER MECHANISM/MAGNETIC FAILURE
C. DISPLAY SWITCH CLUSTER (DSC) FAILURE
Yale GDP155 has a 502317-2 error code and reduced functions. Any information on this code?
I have a fault code 52423-7 on a Yale. What dose it mean
I think you missed one number 52423?
Greetings,
I have electric forklift yale erp 20vt mwv have error code 33209
Can some one help & advice
Hi,
We have Hyster Model R1.50 EX 102. Error code shows #602. Can you please help me? Thank you in advance!
Hello.
I have a Hyster H3.5 FT from 2007.
When I turn on the ignition the display says 522762-4 Truck disabled and the won’t start.
When I look in the diagnostics there’s 40 more error codes.
VSM 522755-3
VSM 524225-0
VSM 524240-3
Hydr 523257-3
VSM 676-4
VSM 2350-3
VSM 522760-4
VSM 524230-3
VSM 522764-3
VSM 676-3
VSM 524269-7
VSM 522762-4
VSM 677-4
VSM 524269-3
VSM 524215-3
VSM 524213-1
VSM 522766-3
VSM 524237-3
VSM 524238-3
VSM 524261-1
VSM 522766-4
VSM 523860-4
VSM 522712-4
VSM 522713-4
VSM 524275-4
VSM 524223-4
VSM 524263-1
VSM 2236-12
VSM 524213-4
VSM 168-4
VSM 522710-4
VSM 522711-4
VSM 100-4
VSM 110-3
VSM 522780-3
VSM 522781-3
VSM 523780-4
VSM 523859-4
VSM 51-7
VSM 524248-2
What can I do to get it running again?
Best regards. Jens.
Please check here
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
sorry wrote it wrong it’s 524224-0
Please check the error code here
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
I have a Yale forklift model number GLC 050 vxnvre085 it has a fault code of 2000-12 said something about the CANRX fault. I have no idea what the CAN Rx is, will somebody please inform me
DTC 2000-12 – CANbus Comm Error VSM
DTC 2000-12 – CANbus Errors (Mazda ECU)
DTC 2000-12 – CAN Tx Failure
DTC 2000-12 – CAN Rx Failure
POSSIBLE CAUSE
A. TERMINATION RESISTOR(S) OPEN CIRCUIT
B. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO
C. CAN HI AND CAN LO SHORTED TOGETHER
D. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES
E. STG ON CAN HI
F. STS/STB ON CAN LO
G. CAN CONNECTED DEVICE FAILURE
I don’t know where it’s located at or how to find it on the forklift
What causes and how do I remedy the situation on a error code 522660-0 , and a error code 522655-1?
Thankyou.
please check here https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
How do I locate the can bus on a Yale forklift model GLC 050 VXNVRE085
We have a 2010 Yale GLP030VX. Serial Number C810404158H
Error Code 522660-1 appeared on the screen. Tool light came on for a while. Then went off. Now it is flashing once in a while. Forklift continued to run just fine. What does this mean and what is needed for repairs?
Please check here https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
Need help with 2 codes on a jx50 please 21008 & 8976
i have a 5tonne hyster forklift and is giving error code 522762-4. what should i do?
DTC 522762-4 – Switched Battery Voltage 3 (IGN 3) OORL
POSSIBLE CAUSE
A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY
B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND
C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND
D. FUNCTIONAL FAILURE IN CONTROLLER
Yale fork lift error code 65299?
Hi,
I’m working on a Hyster S70FT and it has a code that is not on your list, or at least the find function can not find it.
The code is 524263-1.
Any help is appreciated.
DTC 524263-1 – Uncommanded Power Down
POSSIBLE CAUSE
A. TCU PROGRAM CORRUPTED OR TCU APPLICATION FILE MISMATCH
B. FUNCTIONAL FAILURE IN CONTROLLER
looking for cause of a 522655 fault code. vehicle sputters and misfires. barely moves. when i turn the steering it shuts down.
CODES
DTC 522655-0 – Short Term Closed Loop Correction Bank 1 Less Than NOR -40% (Rich Engine Operation)
DTC 522655-1 – Short Term Closed Loop Correction Bank 1 Greater Than NOR 40% (Lean Engine Operation)
DTC 522660-0 – Long Term Closed Loop Correction Bank 1 Less Than NOR -35% (Rich Engine Operation)
DTC 522660-1 – Long Term Closed Loop Correction Bank 1 Greater Than NOR 35% (Lean Engine Operation)
POSSIBLE CAUSE
A. PROBLEMS THAT MAY CAUSE LEAN ENGINE OPERATION
B. PROBLEMS THAT MAY CAUSE RICH ENGINE OPERATION
C. SENSOR FAILURE
D. FUNCTIONAL FAILURE IN CONTROLLER
Error code 4 on a clack model tm20
Hello,
I have an electric lift truck , yale m# erp040thn36te084, while driving the operator said that it would not function, lift, tilt, or side shift and reported that there is an error code on the display. 208 is the only thing it shows, no dash, no other numbers or symbols, except for the flashing red wrench.
Please advise, thank you.
Could you please advise as to the definition of error code E682 on a Hyster 60XT ser.# A380V01611P?
Yale ERP030vtn36te082 error code 4115 what is it
Hello
I have a YALE forklift model GDP 35VH One 2195.
Displays error 522772-3 and the switch turns off
DTC 522772-3 – Backup Lamp Driver Output OORH
POSSIBLE CAUSE
A. LAMP DRIVER OUTPUT SHORTED TO BATTERY
B. INTERMITTENT SHORT OR OTHER POWER SOURCES
C. FUNCTIONAL FAILURE IN CONTROLLER
Hello
I have an error code 882-4 on my Hyster S40FT , what is it please ?
DTC 882-4 – Tail/Marker Lamp Driver Output OORL
POSSIBLE CAUSE
A. LAMP DRIVER OUTPUT SHORTED TO GROUND
B. FUNCTIONAL FAILURE IN CONTROLLER
Hyster 2.5 Fortens
Release “”2″” button
What does that mean. What can i do??
Hi I have a TCM FB30-7 with an error code 106, please can you assist?
Maybe seat switch just check any switch
from the seat or any switch
Dashboard says starter interlock. And code 524225-0
Model? please
Hello,
Have a Hyster Matric 2.0 Electric Forklift
Coming up with KS Open error
Forklift unable to operate or move
I am Working on a Yale GDP155VX. I understand they have an inching valve for when you are trying to slowly approach something. The issue I am having is this one goes into neutral and when you let off the braking pedal it does not go back into forward or reverse until you are pressing the throttle, then when it does go into gear it jolts forward. We do a lot of overhead lifting with long lengths of pipe, it’s creating a safety issue. Talking to the local Yale specialists who stated the wiring harness on the transmission was bad, and sending a low voltage signal to the speed sensor. installed the new one today, nothing changed. It’s also popping the codes 522781-3, 522780-3 and 524250-14. Where should I start on my diagnoses, I’m not a parts changer but clearly the “specialists” are.
Yale veracitor 60 VX keeps stopping with error code 524223-1 any help would be appreciated
please check here: https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
Aloha, I have a Crown C5 we had for about 3 years now and this is the first time this error came on and we can not move the lift. The error says park. PARK BRAKE EREOR. Is this something simple or easy way to repair or fix this.
Mahalo’s
James
E50z-27 wont go forward or backward other operations work fine. When pressing pedal while in forward screen shows the – blinking number 5
Forklift charges is giving the message of
Mains Missing
And the electric forklift is on all night, yet it does not charge.
Hi, we have a Yale forklift model #GLP050VXEURE090 that has two codes: Fault 524251-1 Truck Disabled and Fault 522761-4 & below that code is TEMP__> (hourglass figure 06510). I couldn’t find either fault codes in the list above. Could you please help us out? Sorry if this is a duplicate request.
DTC 522761-4 – Switched Battery Voltage 2 (IGN 2) OORL
POSSIBLE CAUSE
A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY
B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND
C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND
D. FUNCTIONAL FAILURE IN CONTROLLER
Hello, We recently purchased a used Hyster 100 Fortis and now we are getting an error code 522780-2 and are not sure what that means
DTC 522780-2 – Foot Pedal Switch Input Data Incorrect
POSSIBLE CAUSE
A. MONOTROL® SWITCH CIRCUIT OPEN
B. FUNCTIONAL FAILURE IN CONTROLLER
Yale erc060vg error codes 13380 and 33057 drive and Hydraulic locked out
Orange screen of death on keypad display
078 VACC NOT OK
i heve a yale for lift model GLC100VXNGSEO84 SERIAL E818V02549F
fault 524284-3 hidraulic interloc
THR PTOBLRM IS NO LIFT
DTC 524284-3 – Lift/Lower/Return Coil Driver OORH (Main Control Valve)
POSSIBLE CAUSE
A. COIL DRIVER OUTPUT/DRIVER RETURN SHORTED TO BATTERY
B. COIL DRIVER OUTPUT/DRIVER RETURN OPEN CIRCUIT
C. VALVE COIL OPEN CIRCUIT
D. FUNCTIONAL VALVE FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Yale Model A16333285 Error code 524225-0
Please check This link:
https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
I HAVE AN ERROR CODE 96-3 ON A 2008 YALE FORKLIFT . I WOULD LIKE TO KNOW WHAT IS. THANK YOU .
DTC 96-3 – Fuel Level Sensor/LPG Switch OORH
POSSIBLE CAUSE
A. SENSOR SIGNAL SHORTED TO BATTERY
B. SENSOR SIGNAL/RETURN OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO GROUND
D. SENSOR FAILURE
E. FUNCTIONAL FAILURE IN CONTROLLER
Hyster model B80ZHD S/N B257. Having an issue with code 32052 combi throttle sensor fault
I have a Hyster of 7 tons which display the error code 524261-1
what does this error signify
Please check the error here https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
hi I have 7T Hyster with error 52360-0. Can anyone help??
Hi,
I think you missed a one-digit number!
Hi I have a Hyster 30-12 (30 Ton) and it has slow brakes i.e., When you step on service brake pedal it takes a short while for it to stop. There is also an error of 05721 though I’m not sure if it is related to it.
I have a Raymond model 8210 forklift with an error code 0523. What does that mean?
Hyster 80 forklift fault code 524251-1 truck disabled need help
DTC 524251-1 – 5 Volt Supply Circuit C OORL
POSSIBLE CAUSE
A. 5 VOLT “A” SHORTED TO GROUND
B. 5 VOLT “B” SHORTED TO GROUND
C. 5 VOLT “C” SHORTED TO GROUND
D. VSM FAILURE
E. 5 VOLT POWER SUPPLY SHORTED TO GROUND
F. FUNCTIONAL FAILURE IN CONTROLLER
I’ve got a hyster j30xmt throwing code 12575 display works that’s it
I am working on a GDC155Vx
codes
524263 1 #4
157-18 #14
521982 4 #1
627-2 #!
168-4 #15
111-18 #18
DTC 524263-1 – Uncommanded Power Down
POSSIBLE CAUSE
A. TCU PROGRAM CORRUPTED OR TCU APPLICATION FILE MISMATCH
B. FUNCTIONAL FAILURE IN CONTROLLER
DTC 521982-4 – Switched Battery Voltage 3 (IGN 3) OORL (TCU)
POSSIBLE CAUSE
A. IGN 1 OR IGN 3 VOLTAGE OUTPUT OPEN SUPPLY
B. IGN 2 VOLTAGE OUTPUT SHORTED TO GROUND
C. IGN 1 OR IGN 3 OUTPUT SHORTED TO GROUND
D. FUNCTIONAL FAILURE IN CONTROLLER
CIAO HO UN CARRELLO YALE GDP50 CON QUESTO CODICE ERRORE VSM 523925- 4 # 23 SAPETE DARMI QUALCHE INDICAZIONE GRAZIE MILLE
DTC 523925-4 – Range1/FWD2/REV1 Return Circuit OORL
POSSIBLE CAUSE
A. COIL DRIVER/DRIVER RETURN SHORTED TO GROUND
B. FUNCTIONAL VALVE FAILURE
C. FUNCTIONAL FAILURE IN CONTROLLER
I have a hyster 360 had and the def light is on and it’s reading 2 codes
E4863 and E 3714 what can I do it has derailed the machine
Marotti me8c having code 02a50
clark cd80. 06:Warning E/Shut arızası nedir.
code vsm 524245-4 what is that code
DTC 524245-4 – Operator Presence System Sensor OORL
POSSIBLE CAUSE
A. SENSOR SUPPLY OPEN CIRCUIT
B. SENSOR SIGNAL OPEN CIRCUIT
C. SENSOR SIGNAL SHORTED TO SENSOR GROUND
D. SENSOR SIGNAL SHORTED TO FRAME GROUND
E. SENSOR FAILURE
F. FUNCTIONAL FAILURE IN CONTROLLER
How to fix E1506 error code for Hyster
We HAVE A HYSTER 120 ERROR CODE 3701-15 ASKING FOR REGENERATION, WE HAVE TRIED SEVERAL TIMES TO REGENERATE , IT GOES THROUGH THE COURSE BUT DOES NOT CHANGE THE LIFT, IT IS IN LIMPH MODE
Toyota 8HBW23.
Code E250
E250 is the charger in sleep mode. Plug it in for a few minutes to wake it up. If that doesn’t work, check the display for a version from the charger. It could be a communication problem from the charger.
what means error code 3701-16?
Please provide the Brand, Model of the lift truck (forklift)
Hyster J 1.8 XMT sn. G160A053342 vika koodi 245 ?
Hello we have a haytat 60xt firk lift throwing out a 641 code what can this mean
We have a N35ZRS2 sn# B265N02285P with code 40085, steer key input voltage OOR. Any idea what this means or what to look for? Thanks
We have same code John, did you have any luck?
Buen dia, tengo un patin electrico marca Yale medlo MPW060LEN24T2748 que no avanza ni tampoco levanta y marca en pantalla CODE 33, su ayuda porfavor…. saludos
Hi,
I have a Hyster E5.5XL and it has come up with this code – please can you help
Active fault code – Data Key 5 1/4
Hello,
We have a Hyster J302T with a 91 on the display with a red flashing wrench. The Hyster repairman could not determine the issue.
Hi.
3T Diesel Hyster forklift. Error code 26 showing on dash.
What is the error?
F-49 input communication error
Brand? and model?
Hello,
We have a Hyster S1.6 and it shows the error code: AL 68.
Can you tell me what the issue is please?
Thanks in advance.
I HAVE FORKLIFT 7 TON SERIAL NO J006E01529J IT GIVE ME FAULT CODE 522800-13 PLS HELP
What does TI 33073 and DD 33073 and CO 33056
WE ARE USING YALE FORKLIFT MODEL ERP20VT MWB AND WE HAVE SOME ERROR ON THE DISPALY 12592.
A935 – K160 D203 Motor Controller Capacitor Failure:
DTC 12592 – Capacitor Charge
Hyster forklift model E60xn-33 is sending a fault code #22541. I believe that is a display bbutton 0. What is the problem?
Hello.
We have Hyster D456T05451T, and time after time we get this code on screen 141A02. Forklift is mowing very slow and not lifting up the forks. After day or two this problem is gone and all work perfectly, Any ideas?
Hi everybody!
We have a Still forklift,Model FM-X-17.Currently it is having a stopping error, error codes are A5022 and Z1216. If anyone knows how to fix this, please help!
A5022: Traction motor overtemperature, Traction motor too hot,
. Check the traction motor fan
. Check the temperature sensor
. Check the wiring
Hi. We have a hyster j40xnt that just suddenly died and the fault code is 33029. Any help would be greatly appreciated. Thanks
This code indicates a loss of communication between the system manager and the pump controller through the Canbus.
check your connectors at the VSM and the hydraulic controller. The wires you need to check are the green/ yellow twisted pair. And also there could be a failure in one of the controllers.
I have a Yale GLC050LX was working fine. Used it for a few hours one day. Shut if off, come back to use it again, start it up, it starts and runs but wont go into gear(forward or reverse) and can’t use any of the hydraulic levers, they are stiff. So it just sits there running and nothing else. Shut if off and tried again and same thing. No codes but I did notice parking light has been staying on lately even though its not engaged.
Any ideas?
I’m using a Toyota walkie stacker 8BWS10 and I keep seeing a E159 error code along with 3 beeps when I turn it on. I can’t seem to find any information about it in the manual. Any insight would be appreciated. Thanks
ETAC detected a problem with the CAN-bus.
Possible Cause with
Corrective
Actions/Checks:
1. Short or open circuit in CAN-bus wiring.
2. Electrical noise in CAN-bus wiring caused by a bad connection, outside
interference, or low voltage:
a. Check CAN-bus wiring.
b. Try driving using a known-good battery.
c. Try driving in a different environment.
3. Faulty power amplifier. Check the power amplifier.
4. Faulty ETAC.
I show a 12833 code. Also a circle with a one inside,says truck disabled due to(single) traction controller
What is the brand? and model?
Toyota 8HBW23 pallet jack with c 72 code
traction motor stalled
Toyota 8HBW23 gives a C 72 code and seems to not release the brake. Sorry if this is a repeat post…I don’t see my post that I previously submitted. Thank you.
Limited traction performance until code is cleared. The brake is activated when the engine stalls. Reason TA detects that the traction motor has stalled for 5 seconds. Tests to Run Use the service key and test the traction motor encoder by scrolling to the RPM display (D) in the diagnostic screens and command the motor to run. The displayed value is the engine speed as reported by the TA.
We have a TCM 4-way reach forklift model FRB25-8M and I am getting an error code 508.I think it has something to do with the electric power assisted steering as it is very hard to steer.Would anyone know what code 508 is for?
Error code 508: typically indicates a problem with the controller area network (CAN) communication system. This error code may indicate a problem with the wiring or connections in the CAN network, a defective control module, or a malfunction in the software.
Please I need help for Yale model FB20PYE with error code 150 AND 153
Error code 150 specifically indicates a “Forward/Reverse Pedal – Out of Range High” fault, while error code 153 indicates a “Throttle Pedal – Out of Range High” fault.
These faults can be caused by a variety of issues, including a malfunctioning accelerator pedal, a faulty sensor or wiring, or a problem with the controller.
I have an Hyster R30XM3 and getting error code 30250 traction platform hung. Do i need a tech to resolve this?
hello, i have a hyster electric forklift 4wheel, it not energerzing, no power when i connect the battary, please what is the possible cost, tank
There could be a number of various causes for your Hyster electric forklift to not turn on when the battery is connected. Without more information, it’s difficult to estimate the cost of repairs. The followings are a few potential reasons and their associated costs:
Dead battery: A new battery may be required if the old one is fully dead. The size and kind of battery your forklift needs will determine how much a new battery will cost.
Charger malfunction: The battery may not be receiving a charge if the charger is malfunctioning. The kind and brand of charger required will determine the price of a new charger.
The contactor, which allows electricity to pass to the motor, is malfunctioning. The forklift might not energize if the contactor is malfunctioning. The model and brand of your forklift will affect the price of a replacement contactor.
Faulty controller: The controller is responsible for regulating the speed and direction of the forklift. The forklift might not ignite if the controller is malfunctioning. The model and brand of your forklift will determine the price of a new controller.
Hello!
Please help, error 128 02 on the loader Yale ERP18VF MWB, S/N G807B05273L. What’s it?
Thank you in advance!
Error 128 02 on the Yale ERP18VF MWB loader indicates a fault with the accelerator pedal position sensor. This sensor is responsible for detecting the position of the accelerator pedal and sending a signal to the engine controller to adjust the speed of the loader accordingly.
To resolve this issue, you may need to check the wiring connections to the accelerator pedal position sensor and make sure they are properly connected. If the wiring connections are ok, you may need to replace the sensor.
Have a Hyster N45ZR2 Keeps throwing codes 40060, 40062, 10104, 90104, 90075. What can the issue be?
An electric narrow-aisle reach truck is the Hyster N45ZR2. The following problems are indicated by the error codes you provided:
40060: This code indicates an issue with the traction motor thermal sensor.
40062: This code indicates an issue with the lift motor thermal sensor.
10104: This code indicates an issue with the encoder signal from the drive motor.
90104: This code indicates an issue with the encoder signal from the lift motor.
90075: This code indicates an issue with the brake switch or its wiring.
These error codes suggest that there may be problems with the motors, their associated heat sensors, and the encoder signals coming from the motors. Moreover, there can be a problem with the wiring or brake switch.
Code 13368, no problems, normal function but at they start, flashes they code, but everything it’s work normaly.
Bat charge 36.7v cell are 2.0v ± 0.2
What is the brand of your forklift and model too?
I have a Raymond 8210 pallet jack
I’m getting the code E250 and stop working and an alarm goes off , to get it back to work I have to turn it off and back on , then works till happens again
Code Title Communication Error with the HF Charger
Operator Display E250
System Response No truck function active
Reason HF Charger CAN communication issue.
Tests to Run None
How to Clear Verify the CAN cable to the battery pack is connected.
Code will self-clear after plugging the charger into AC power to reset the charger
from sleep mode.
Hello, I have a STILL FDX 20N, it has not been used for a while and now when I charge the battery and try to start it, it shows error T 254… Can you help me to start it? Thanks in advance
Добрый день! Электропогрузчик Yale ERP16VF (A955) кода ошибок 21063 и 16508 помогите расшифровать
The error codes 21063 and 16508 on a Yale ERP16VF (A955) electric forklift may indicate the following issues:
Error code 21063: This is a CAN communication error code. It may indicate a problem with communication between the various electronic modules of the forklift, such as the traction controller and the lift controller. This error code may also occur if one of the modules is faulty or damaged.
Error code 16508: This is a low battery error code. It may indicate that the forklift battery is not sufficiently charged, or that it is nearing the end of its life. It may also indicate a problem with the battery charging system.
Here are some steps you can take to diagnose these error codes:
For error code 21063, check all electrical cables and connections to ensure they are properly connected and not damaged. If the problem persists, it may be necessary to replace one of the faulty electronic modules.
For error code 16508, check the battery voltage to ensure it is sufficiently charged. If the battery is nearing the end of its life, it may be necessary to replace it. Also, make sure that the battery charging system is functioning properly.
Hi, I have a BT C4E160 and show error 2B
The error code 2B on a BT C4E160 could indicate a fault with the control system
In general, some basic steps you can take to troubleshoot this type of issue include:
Check the power supply to ensure that it is connected and functioning properly.
Inspect the control system to ensure that all wires and connections are secure and in good condition.
Verify that the settings on the control system are correct and that there are no programming errors.
Hi I have a Cat error codes number 0181 and 3102
Clark is not responsive
Hi,
Model of your forklifts?
Hi i have a Toyota BT Vector with error code: 01:508? I can start but not drive even in safe mode
Error code 33057 not found
Forklift brand?
Model?
I have13336
Error Code 0224 Toyota Model 8FE18T
HI I have an error code of 15 and 18 on a Komatsu FG25T16, any help would be appreciated.
Hi, i have a Steinbock Boss LE 16 and the error massage is
A:10
Hi dear
i have Doosan fork lift D110s-5 model 2007
The problem when turn on the fork lift and put the automatic gear from N to L or R not drive forward and reverse.
EEcode flashing appeared on the screen fault also (P) symobl on. until after press pressure break .
I checked the fuse is ok also the realy is work from the signal input automatic gear .
Where the lift lever and tilt lever work normally when switch on the fork lift .
How can i found solution to solve this problem?
E646 error code
How do you clear a code on a kbd 35 baoli forklift? Error code is 190-9
Hi. I have 25 mitsubishi europea
Model: FB25K-PAC
N.S : EFB8C 51188
3250kg
CODE ERROR 1 : ( 14 )
CODE ERROR 2: ( 55 )
Thank you so much
I have a Raymond 470 sitdown counterbalance with error code E2 and 86. Cheers.
2006 Yale 50VX Fork Lift GLP050
Fault Code 524264-2 (No Trans Braking)
please check this link : https://www.forkliftplus.com/en/yale-hyster-forklift-error-codes/
I have a hyster 60 with 2.4 gm on propane. I’m getting codes 522652-6 522608-6 and 07798. My problem is Sinton truck starts other times it doesn’t. If these codes show up or does not start . When this started it was only 522608-6. Now these other codes originated
Hello,
We have a Yale MR20HDA and its throwing an error code that reads Reset Enc.
I have crown C5 forklift with code 108.21 any help on this
Hi I have a hyster H155 diésel and i have a fault code 882-3 then it says 30 seconds until shutdown
DTC 882-3 – Tail/Marker Lamp Driver Output OORH
POSSIBLE CAUSE
A. LAMP DRIVER OUTPUT SHORTED TO BATTERY
B. INTERMITTENT SHORT OR OTHER POWER SOURCES
C. FUNCTIONAL FAILURE IN CONTROLLER
I have Hyster R30XMS2: with
Height error
Hi, I have a Hyster H 12.00 XM and it has code E5304 displayed. I cant find information for this code anywhere. Any help would be greatly appreciated.
Thank you.
Check the inching (throttle pedal) for wiring damage or lost connection
hyster E50xn code 12832
DC Bus low. Check the motor/motor controller wiring. Check your battery voltage.
Good morning, I have an older Electric Hyster Forklift, – J40ZT Serial# 160N05006H, it keeps throwing codes 210, 241, and 246.
Can you tell what these codes are, and do you know anywhere I can get a list of error codes. Thankyou.
Hola tengo un raymond 750, al llegar a cierta altura el cldigo 64 ya revisamos valvulas bobinas, controlador, cables, contactores, sensores de elevacion y nada, si nos podrian apoyar se los agradeceria mucho
Code 64 – No Pulses Seen from
Height Indicator Encoder
With the lift pump running or
SOL2 energized, the first mast limit
switch is open, but the VM
detected no pulses from the Height
Indicator encoder.
I have unit Hyster, Japan model J1.75EX with error code 42 did you have error list for this model, I have error for J1.75EX-2 not same for this model
Hi I have a Yale 155
Error code 523612-5
I have read a comment saying it was pressure pump to high but what pump would it be though?
Hi, the codes error for my hyster lift truck model 30 are 12546, 2541, 2567,
I have a Yale glc050 forks won’t lift up or down throwing a fault code of 2236-12
What code is this looked it up and have found no results
DTC 2236-12 – CANbus Comm Error With MLM
POSSIBLE CAUSE
A. TERMINATION RESISTOR(S) OPEN CIRCUIT
B. OPEN/INTERMITTENT CIRCUIT ON CAN HI, CAN LO
C. CAN HI AND CAN LO SHORTED TOGETHER
D. OPEN CIRCUIT ON POWER/GROUND TO CAN CONNECTED DEVICES
E. STG ON CAN HI
F. STS/STB ON CAN LO
G. CAN CONNECTED DEVICE FAILUR
Hello
Yale forklift , error d000 , pls help
Hello
Yale Forklift Alarm code 8976 Model: ERP22-35VL ,pls help
Clark Forklift C25CL, Error code: PIN27 S/C GND. Thank
Error code co20 on hyster 3.0 model. Not going forward or back
I have a Hyster 30 with ERR CO30 flashing on the dash with a spanner. It is not due for a scheduled service yet and it appears to be running OK except for very tight steering.
bonjour sur un chariot elevateur Yale electrique ERP15vt code erreur 33051 et33057 merci pour votre aide
Hi i have a H3.5xt 2018 model , its showing Error C050 , your help would be greatly appreciated,cheers Matt
Toyota H2-4
Hyster j40xnt fallas 12808, 12810 motor tracción izquierdo no trabaja bien
i can not find error 1231-12 in yale list
Hello, the codes are flashing
248A02, 248B02
Yale MS16
please what does it mean and what to focus on
well thank you
Yale forklift with error 12832 and shows a wrench underneath it
Park Brake/Mast Tilt Position Sensor Out of Range Low (OORL):
12832 – Park Brake Position
Yale error code 12808
Yale error code 33051 ?